A 26-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports as shown. At A, a 25-mm diameter bolt is used to connect the rod to the support. Determine the normal force in steel rod (1) after the temperature drops 60°C. Use E = 200 GPa and a = 11.9 × 10 % / °C. 4 54.9 KN O 68.8 KN 90.0 KN O 75.8 KN 48.6 kN B

A 26-mm diameter by 3.5-m long steel rod (1) is stress free after being attached to rigid supports as shown. At A, a 25-mm diameter bolt is used to connect the rod to the support. Determine the normal force in steel rod (1) after the temperature drops 60°C. Use E = 200 GPa and a = 11.9 × 10 % / °C. 4 54.9 KN O 68.8 KN 90.0 KN O 75.8 KN 48.6 kN B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A rigid bar AB is hinged at A and is supported by a rod CD at C. The rod is pin connected at D, as shown. Neglect deflections of the bar due to bending. Use E=200 GPa. If the allowable stress in rod CD is 120 MPa, what weight W in kgs can be safely applied?
A steel strip of length L = 200 mm is fixed at A and rest at B on a vertical spring of stiffness k = 2N/mm. The steel strip is 5 mm wide and 10 mm thick. A vertical load P = 50 N is applied at B as shown. Consider E = 200 GPa, the force (in N) developed in the spring is A L P B K
roblem 2: A steel hoop, 10 mm thick and 80 mm wide, with inside diameter 1500.0 mm, is heated and shrunk onto a steel cylinder 1500.5 mm in diameter. What is the nor- mal force in the hoop after it has cooled? Neglect the deformation of the cylinder, and use E == 200 GPa for steel. roblem 3: The timber member has a cross-sectional area of 1750 mm² and its modulus of elasticity is 12 GPa. Compute the change in the total length of the member after the loads shown are applied. 40 kN 35 kN 20 kN D• A
1. The rigid bar ABC is supported by a pin at B and two vertical steel rods. Initially the bar is horizontal and the rods are stress-free. Determine the stress in each rod if the temperature of the rod at A is decreased by 40°C. Neglect the weight of bar ABC. Use a=10.7 x 10-6/°C and E=200 GPa for steel. A = 1500 mm². - A = 500 mm² 1.5 m 1 m A В k 0.8 m → 1.5 m
5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft. A D TB 0.5m Tc 0.9m с 0.4m 40mm ↑ TB-10KN-m Tc=15KN.m
Mechanics of Deformable Bodies 6 in. in.- 5 in. 4 in. A steel tube with the cross section shown carries a torque T. The tube is 6ft and has a constant wall thickness of 3/8in. (a)Compute the torsional stiffness k=TTO of the tube. (b) If the tube is twisted through 0.5°, determine the shear stress in the wall of the tube. Use G=12x 106psi.
Three aluminum rods support the rigid L-shaped bracket BCF as shown in the figure. Determine the stress in rod DE (express answer in MPa) if rod FG is cooled by 50°C. All three rods have the same cross-sectional area of 1000 mm^2. Use 73.1 GPa and 23 x 10^-6/°C for the modulus of elasticity and the coefficient of thermal expansion of aluminum, respectively.
Computation must be completeAnswer in two decimal placesBox your final answer
Solve a part only in 20 min and take a thumb up plz
Situation 10: The rigid bar ABC as shown in the figure is pinned supported at B and attached to the vertical two rods. Initially, the bar is horizontal and the vertical rods are stress-free. The temperature in the steel rod is decreased by 40°C. Neglect the weight of the bar Steel L = 910 mm A = 300 mm² E = 200 GPa a = 11.7 x 106/C AT = -45°C 0.5 m + 1.3 m Aluminum L = 1320 mm A 1200 mm² E = 70 GPa a = 23 x 106/C 27. Determine the stress in the aluminum rod 28. Determine the stress in the steel rod 29. Determine the deflection at the point where aluminum rod and bar is attach
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 16 kips, F2 = 30 kips, and the normal stress in each rod must be limited to 18 ksi, determine the minimum diameter d1 required for rod (1).