5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft.

5 - An aluminum circular shaft, fixed at both ends, is loaded by torques applied at points B and C, as shown in the figure. The bar material has a shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist along the length of the shaft.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Problem #4: The aluminum shaft consists of two segments AB and BC (G = 27 GPa). Shaft AB is a solid…

A: Given data For portion AB LAB = 1.15 m = 1150 mm D = 60 mm For portion BC LBC = 0.75m = 750 mm…

Q: Two thin-walled tubular members made of the same material have the same length, same wall thickness…

Q: A 16 mm steel bar AB and a 25 mm steel bar BC support a load P = 7,500 N as shown. If E = 200 GPa,…

A: Given data: Diameter of AB steel bar=16 mm Diameter of BC steel bar=25 mm Load=7500 N It is asked…

Q: A tie-down on the deck of a sailboat consists of a bent bar bolted at both ends, as shown in the…

A: Given:

Q: maximum value for the load R.

Q: The shaft shown consists of a steel tube (1) bonded to a brass core (2). The shear modulus of steel…

Q: A hollow section bar has an outside diameter of 120 mm and an inside diameter of 60 mm. If the shear…

A: Ro = Outside radius = 1202 = 60 mmRi = Inside radius = 602 = 30 mmζy = Shear stress at yield = 100…

Q: t= 10 -Op- (а) (b)

A: Solution Given data Allowable shear stress ζallowbale= 40 MPa= 40*106 Pa Allowable rate of twist θ=…

Q: 400 Material A 300 Material B 200 Material A 100 0.002 0.004 0.006

A: Solution: B) Given Data: Tensile load=88 kNElastic modulus of material A=150 GPaElastic modulus of…

Q: 3. The aluminum shaft, composed of three segments is fastened to rigid supports as A and D.…

Q: A solid brass shaft is loaded as shown below by two torques TB segments are LAB = 750 mm and LBC =…

Q: Shafts A and Bare made of the same material and have the same cross-sectional area, but A has a…

A: Given:The shafts A and B are having same cross-sectional area According to the problem statement, we…

Q: 2. A rod is composed of an aluminum section rigidly attached between steel and bronze sections as…

A: Given data Area of steel=300mm2=300×10-6 m2 Area of aluminium=300mm2=300×10-6 m2 Area of…

Q: A В C 2m 1m 3m P Aluminum A=500mm2 A=900mm? E=70GPA L=2.0m Steel Detail of E=200GPA L=1.25m pin at O…

Q: - 150 mm - 3 mm B 200 mm A 3 mm

A: shear strain is defined as the angular deformation of the object when subjected to shear force…

Q: 3. An aluminum rod is rigidly attached between a steel rod and a bronze rod as shown in the figure.…

A: The free body diagram of the rod is given:

Q: For the shown Fig., find the maximum shearing stress in bronze part of the shaft.

A: Balancing the reactions

Q: a. The beam weighs 3600N. Draw the V and M diagram. b. Assume we do not know the weight of the beam…

A: 1-If Beam weighs 3600 N then drawing of SFD and BMD2- if Beam Weighs is not know then finding of…

Q: A flexible connectoin consisting of rubber pads (thickness t = 9 mm) bonded to steel plates is shown…

Q: Consider a solid circular shaft fixed at one end and free at the other end with a concentrated…

Q: rigid support @ A A 400 N-m 850 N-m L=1.4 m 30 mm diameter L=2.4 m 50 mm diameter L=1.9 m 30 mm…

Q: Q.1. A. For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

Q: Q. A For a hollow steel tube with an inside diameter of 120 mm and outside diameter of 138,…

A: Note:- as per our company guidelines we are supposed to answer only first part. Kindly repost other…

Q: A shaft composed of segments AC, CD, and DB is fastened to rigid supports and loaded as shown in the…

A: Given:- A composite shaft fastened to rigid supports having Modulus of Rigidity as…

Q: P A (0) B (2) (3) FIGURE P1.6/7 P1.7 WP Axial loads are applied with rigid bearing plates to the…

Q: hollow titanium [G= 46 GPa] shaft has an outside diameter of D = 56 mm an tress in the shaft must be…

Q: Using an Permissible stress of 155 MPa, determine the maximum bending moment M that can be applied…

A: Given, An, I section beam, Allowable stress, σ = 155mpa Find out:- maximum bending moment,

Q: A solid 2.95 in. diameter shaft is subjected to a torque of T-305 lb-ft and an axial load of P-4700…

Q: It is made of solid circular cross-section bars, whose geometry and loading condition are given in…

Q: A steel shaft with a constant diameter of 50 mm is loaded as shown by applied torque. Use G=83 GPa.…

Q: A one inch diameter machined steel cantilever 10 in. long is loaded on the end with a force that…

A: Note : As per Bartleby guidelines policy,I have answered only 1st 3 subparts.If you need remaining…

Q: Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure.…

Q: Part 2 * Your answer is incorrect. The z-component of momemt M will cause compression at A and B,…

Q: b 7'

Q: 02: For the stresses at the point shown, find: • The maximum shearing stress. • The principal…

Q: 120 mm 750 mm 300 mm 1.0 mm

A: Given data Triangular shape Dimensions To find Shear strain

Q: The cross section of the AB part of the welded pipe part given in the figure is a hollow pipe and…

A: Given: The inner diameter of the pipe AB is 20 mm. The outer diameter of the pipe AB is 28 mm. The…

Q: A steel tube with the cross section shown is 3 m long and has a wall thickness of 4.8 mm. (a) If the…

Q: determine the stress in each rod after the load after the load P = 30 kips is applied

A: Given- The light rigid bar ABCD as shown in figure is pinned at B and connected to two vertical…

Question

5 - An aluminum circular shaft, fixed at both ends, is loaded by torques
applied at points B and C, as shown in the figure. The bar material has a
shear modulus G = 85 GPa. Plot the maximum shear stress and angle of twist
along the length of the shaft.
A
D
TB
0.5m
Tc
0.9m
с
0.4m
40mm
↑
TB-10KN-m
Tc=15KN.m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step 6

Trending now

This is a popular solution!

Step by step

Solved in 6 steps with 6 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Steel bar of cross-section 550mm2 is acted upon by the forces shown in figure. For steel, E = 200GPa. Compute the stress in BC Compute deformation of AB Compute the total elongation of the assembly.
SOLVES STEP BY STEP, USE TABLE IF NECESSARY
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P=34 kips is applied to the assembly at A, two loads of Q=25 kips are applied at B, and two loads of R=37 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 16 ksi. The normal stress magnitude in steel rod (2) must be limited to 32 ksi. The normal stress magnitude in brass rod (3) must be limited to 24 ksi. Determine the minimum diameter (in in rounded to the nearest thousandths) required for rod 2.
Axial loads are applied with rigid bearing plates to the solid cylindrical rods shown in the figure. One load of P = 30 kips is applied to the assembly at A, two loads of Q = 20 kips are applied at B, and two loads of R = 35 kips are applied at C. The normal stress magnitude in aluminum rod (1) must be limited to 15 ksi. The normal stress magnitude in steel rod (2) must be limited to 33 ksi. The normal stress magnitude in brass rod (3) must be limited to 22 ksi. Determine the minimum diameter required for each of the three rods. (1) R В D di in. d2 = i in. dz = i in.
Mechanics of deformable bodies.
A hollow titanium [G = 43 GPa] shaft has an outside diameter of D = 46 mm and a wall thickness of t = 1.23 mm. The maximum shear stress in the shaft must be limited to 118 MPa. Determine: (a) the maximum power P that can be transmitted by the shaft if the rotation speed must be limited to 22 Hz. (b) the magnitude of the angle of twist in a 830-mm length of the shaft when 17 kW is being transmitted at 9 Hz. Answers: (a) P = (b) = i kW. O
The frame supports the distributed load shown. Determine the state of stress acting at point E. Show the results on a differential element at this point. The section is composed of two materials where E₁ = 200 GPa, and E₂ = 150 GPa AC xxxx E. 4 kN/m -1.5 m 1.5 m--- -3 m 3 m BA 20 mm 60 mm 20 mm 5 m E 50 mm E₁ = 200 GPa E₂ = 150 GPa
6- A circular shaft is composed of a steel core and a brass covering, as shown in the figure. Under the applied torque, what is the maximum shear stress in each material? The composite shaft is attached to a wall at A. B O T= 5 KN•m Steel core r=15mm G=78 GPa bross cylinder ro=20mm (outer diameter) G=39 GPa
The following composite shaft is loaded as shown in the figure. The AC segment of the shaft is solid; it is connected to the hollow shaft CD with the help of a rigid flange at C. A torque of 100 Nm is applied at B, as shown. A uniformly distributed torque of 200 Nm/m is applied over the entire length of CD (2m), also shown in the figure. Please ignore the thickness of the rigid flange at C. Given: GAC = 140 GPa, diameter of AC = 20 mm. GCD = 200 GPa, inner diameter of AC = 40 mm, outer diameter of AC = 50 mm. a. Determine the absolute maximum shear stress on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Draw the state of stress on a volume element corresponding to the maximum absolute shear stress location. Show proper perspective when drawing the state of stress. b. Determine the absolute maximum shear strain on the shaft. Specify where it occurs along the length of the shaft and on the circumference of the shaft. Be careful…
The solid shaft, made of three different materials, carries the two torques shown. (a) Calculate the maximum shear stress in each material. (b) Find the angle of rotation of the free end of the shaft. The shear moduli are 28 GPa for the aluminum, 83 GPa for steel and 35 GPa for bronze. Aluminum 100 mm -3 m- 4 kN.m Steel 75 mm -2 m 1.5 kN - m Bronze |--15m-l
Solve it