If d = 1 m, and 6 = 30°, determine the normal reaction at the smooth support A if P = 400 N. Neglect the weight of the bar. Express your answer using three significant figures and include the appropriate units. NA = Submit -- NB = HA Value -- My Answers Give Up Part B Determine the normal reaction at the smooth support B. Express your answer using three significant figures and include the appropriate units. Units HA Value ? Units ?

If d = 1 m, and 6 = 30°, determine the normal reaction at the smooth support A if P = 400 N. Neglect the weight of the bar. Express your answer using three significant figures and include the appropriate units. NA = Submit -- NB = HA Value -- My Answers Give Up Part B Determine the normal reaction at the smooth support B. Express your answer using three significant figures and include the appropriate units. Units HA Value ? Units ?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

VI IN Determine the force in each member of the truss. State if the members are in tension or compression. Take that P = 470 lb .(Figure 1) Submit Request Answer Part E Determine the force in the member AB of the truss, and state if the member is in tension or compression. Figure 1 of 1 Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. B μΑ ? 3 ft FAB = Value Units Submit Request Answer -2 ft -2 ft Next >
a = 1 m b = 2 m c = 3 m Force AB = 500 Newtons Find the Projected Force to direction AC in N. (Hint: Dot Product). If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign.
2. A linear spring of stiffness k N/mm is to be designed to stop a railroad car, with a mass of m kg, traveling at v, km/hr within x mm after impact. Find the smallest value of k, in terms of m, ve, and x, that will produce the desired result. Hint: a dx = v dv. mim Vo k wwwM
3. The small sphere shown below has held by two wires with tension To. sphere is released from equilibrium. Determine the ratio To/T1, where T1 is the tension in the remaining wire immediately after the other mass of 2kg. It is initially One wire is cut and the small a one is cut. 30 30
Problem 02.094 - Expression for force in an elastic cord using the position vector The structure consists of a quarter-circular rod AB with radius 150 mm that is fixed in the xy plane. CD is a straight rod where D may be positioned at different locations on the circular rod. GE is an elastic cord whose support at Glies in the yz plane, and the bead at E may have different positions d. For the values of b=4, h=3, d=260 mm, and z=240 mm provided, determine the coordinates of E and if the elastic cord supports a tensile force of 100 N, write a vector expression using Cartesian vector representation for the force FBG the cord exerts on bead E. (Include a minus sign if necessary) 360 mm B 150 mm A The coordinates of point E are EG The Cartesian representation of the force FBG is FBC = ( four decimal places.) and mm. (Round the final answer to the nearest whole number.) ) N. (Round the final answers to
Required information Consider the loading condition given. Take F= 450 lb/ft and P = 150 lb/ft. F A 6 ft 6 ft → B Determine the support reactions for the loading shown. The support reactions are as follows: Ax= g lb, Ay= |lb, and By= |lb.
Please correct my understanding of this question. -In the equation of the moment at point A, there is a value, 36(11.5). I assume that is a force from the distributed load. -If you are finding the moment at point A, wouldn't you only need one value from the distributed load which is 27(10)? So my question is how do you get the value of 36 and 11.5, separately. And what is it for?
The bent rod shown in (Figure 1) is supported at A, B, and C by smooth journal bearings. The bearings are in proper alignment and exert only force reactions on the rod. Figure 2 m 30° 60° F B 1 m C 1 of 1 2 m 0.75 m art A Determine the magnitude of F which will cause the positive a component of reaction at the bearing C to be C = 30 N. Express your answer to three significant figures and include the appropriate units. F = Submit Value Provide Feedback Request Answer Units ?
Beam AB is loadead as shown. If P is 1000 lb, Solve for the ff: • Horizontal support reaction at A and B • Vertical support reaction at A and B Include 4 decimal points in all answers.
A horizontal force F shown in the figure is exerted on a vertical lever to prevent a load (weight W) from falling downwards. The drum can rotate without friction about point B; the coefficient of static friction between the drum and the block is μ0=0.30. Determine the magnitude of the force F (in kN) needed to prevent the drum from rotating. a= 4mb=3mc=1mdiameter of the drum = 4m
Consider the compound beam shown in (Figure 1). Assume C is a roller, B is a pin, and A is fixed. Suppose that w = 16.5 kN/m Figure 3 m B 6 m < 1 of 1 Determine the moment of reaction at A. Express your answer to three significant figures and include the appropriate units. Enter positive value if the moment is counterclockwise and negative value if the moment is clockwise. MA = Submit Part D • Nc = μA 1 D Value Request Answer Determine the normal reaction at the support C. Express your answer to three significant figures and include the appropriate units. μA Value Units 1 @ Units Review ? Your device needs to restart to install update
A 90-kg smooth circular cylinder A with a radius of 0.6 m is held in equilibrium by a cord CD and a bar BC of negligible mass. The length of bar BC is 2.4 m. a. Draw the FBD of the circular cylinder and the bar BC.b. Determine the tension in the cord CD.