The tank is filled with water and kerosene to the depths shown in (Figure 1). The tank has a width of 3.0 m. Take p = 1000 kg/m³, pk=814 kg/m³. Figure A 60° 3 m B 1 of 1 1 m Part A Determine the total resultant force the liquids exert on side AB of the tank. Express your answer to three significant figures and include the appropriate units. FR = Submit x² μA Xb Value Provide Feedback a b Units X. 10m Previous Answers Request Answer X X Incorrect; Try Again; 5 attempts remaining ? Next >

The tank is filled with water and kerosene to the depths shown in (Figure 1). The tank has a width of 3.0 m. Take p = 1000 kg/m³, pk=814 kg/m³. Figure A 60° 3 m B 1 of 1 1 m Part A Determine the total resultant force the liquids exert on side AB of the tank. Express your answer to three significant figures and include the appropriate units. FR = Submit x² μA Xb Value Provide Feedback a b Units X. 10m Previous Answers Request Answer X X Incorrect; Try Again; 5 attempts remaining ? Next >

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 24P

See similar textbooks

Related questions

Q: Analyze the figure below and determine the absolute pressure in the tank. Take the density of water…

A: Please refer the attached image for complete solution. THANK YOU.

Q: Question 2. The manometer in the figure is used to measure the pressure difference between two…

A: ρ = density of water = 1000 kg/m³ g = acceleration due to gravity = 9.81 m/s² h = height difference…

Q: Consider a hydraulic jack being used in a car repair shop, as in the figure. The pistons have an…

Q: Container has some fluid as shown in figure if container is moving with uniform velocity 10 m/s,…

A: Uniform velocity of container V=10 m/s, Pressures- PabsA=130 kPa&Patm=100 kPa. To Find- The…

Q: Situation 22. For the built-up shape shown in the figure, determine: В. bf = 200 mm — 12 тт hE 200…

Q: Consider the opening exposed to the atmosphere at 1 atm, find the pressure at point A. Refer to the…

Q: 1. From the figure shown, the tank contains oil having s specific gravity of 0.80. Oil flows at a…

Q: AE 10W-30 oil flows through the 125-mm-diameter pipe hown in (Eigure 1) with an average velocity of…

A: Diameter of pipe, The velocity of flow, length of a section of pipe, = 10mThe density of oil =…

Q: Problem #4 If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate?…

A: The objective of the problem is to determine the flow rate in a pipe system with known pressure…

Q: Small-diameter, high-pressure liquid jets can be used to cut various materials as shown in the…

Q: SAE 10W-30 oil flows through the 125-1 (Eigure 1) with an average velocity of 1. Figure

Q: a. Water and oil flow in horizontal pipelines. A double U-tube manometer is connected between the…

Q: 10. The cylindrical container in the figure below weighs 400 N when empty. It is filled with water…

Q: The plastic block shown below measures I.5 m xl.S m x(.7 m and has a specific gravity of 0.38. The…

A: Given data: Note : in diagram height is given as 0.5 m is but in question 1.5m is given assuming…

Q: For the tank shown in the figure, compute the pressure at points B, C, D and E in kPa. (Liquid X =…

Q: circular vessel 2 m. in diameter and 3 meters high as shown is filled with liquids A, B and C…

A: Given data, Area of orifice = 0.09 m² Cd = 0.6 Diameter of tank = 2 m Total height of tank = 3 m

Q: A piston with a diameter of 15 cm was placed in a cylinder connected to a 1.27 cm inclined tube…

A: Given data Diameter Unit weight Angle Inclined height To find Weight

Q: An irregular container, closed at the end, is filled with water (999 kg/m3). Consider the opening…

A: Density of water, ρw =999Kgm3The given container is filled with water and left limb is open to…

Q: Pipe AB has a diameter of 40 mm (Figure 1). The pipe and water within it have a total mass of 9 kg.

A: Solution Given Data Diameter= 40 mmTotal mass= 9 kg

Q: For the configuration shown In the figure below what must be the value of the specific weight of the…

Q: If the bottom of a pop bottle similar to that shown in the figure below, what would be the magnitude…

A: Given Air pressure in the top of the bottle = 38 psi Specific Gravity of Pop = S.G of water = 1…

Q: A vertical pipe is shown in figure 1 below. The pipe tapers from 50 mm in diameter to 25 mm in…

Q: An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of…

A: Given: Length of pipe Diameter Viscosity Discharge To find: Velocity Reynolds number Pressure drop

Q: Q6) A hydraulic system is shown in figure Q6. Assume the system is in equilibrium state (There is no…

A: Using Hydraulic press principle one can get Solution for the given parts.fa=FAf=Small weight lifted…

Q: Water flows through a pipe reducer shown in figure 2. The static pressure in the large diameter pipe…

A: Hi! Thank you for the question. As per the honor code, We’ll answer the first question since the…

Q: Kerosene at T = 20°C flows through the 100-mm-diameter commercial steel pipe at 1.11 -1.8 log ()"…

A: pressure drop is normally the difference in the sum of pressure between two different values in a…

Q: 1. The figure shows a tank discharging through a pipe witha nozzle at its end. Find the discharge…

Q: 3.20 As shown, a load of mass 10 kg is situated on a piston of diameter D1 140 mm. The piston rides…

A: Given data in question Mass of object Diameter of piston Specific gravity of oil To find out…

Q: 24.For the tank shown in the Figure, hi = 3m and h3 = 4 m Determine the value of h2. %3D

A: Given: h1 =3m, h3 = 4m and Specific gravity of oil = 0.84 Find: h2= ?

Q: Example 5 A closed tank shown in the given figure, is given an acceleration of 3.6 m/s, the…

Q: The gauge pressure reading at B is used to measure the pressure at point A in a water flow. If the…

Q: Figure shows below a Fluid 1 (SG = 0.88) and fluid 2 (SG = 2.93). If Pa = 98 kPa, determine the…

Q: A large open tank contains water and is connected to a 2-m-diameter conduit as shown. A circular…

Q: A pump draws water from reservoir A and lifts it to reservoir B as shown in the figure. The loss of…

Q: 450 N 220mm 260mm 120mm 60mm

A: Force applied on the lever AB at A, F =450NThe length of lever between A and hinge = 220mmThe…

Concept explainers

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?

Question

The tank is filled with water and kerosene to the depths
shown in (Figure 1). The tank has a width of 3.0 m
Take p = 1000 kg/m³, p = 814 kg/m³.
Figure
A
60°
3 m
B
1 of 1
1 m
Part A
Determine the total resultant force the liquids exert on side AB of the tank.
Express your answer to three significant figures and include the appropriate units.
FR =
μA
xa Xb
Value
a
b
Provide Feedback
Units
X. 10m
Submit Previous Answers Request Answer
X
X Incorrect; Try Again; 5 attempts remaining
?
www
Next >

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Determine the total resultant force

VIEW

Solution

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The distance Ah is the height of the liquid in the manomoter above the heavier liquid in the tank. D 10 cm Water Ah = ? B C 20 cm S= 3.0
A glass 12 cm tall filled with water is invert the pressure at the closed end? Barometric pressure is 101.325 kPa. What is Ans. 100.15 kPaa Problem 2- 51 In Figure 13, in which fluid will a pressure of 700 kPa first be achieved? Ans: glycerin Proble Po 90 kPa A diffe water ethyl alcohol p= 773.3 kg/m³ mm, 1 betwe 60 m ol p= 899.6 kg/m 10 m water P= 979 kg/m' glycerin p = 1236 kg/m 5 m 5 m 2021/04/16 18:27
Problem #4 If the pressure difference between points 1 and 2 is 25 psi, what will be the flow rate? The pipes are galvanized iron with 0.0005 ft. Take v = 1.06 × 10−5 ft²/s and neglect Kis = minor losses. 10 in. dia 1. 2000 ft, 8 in. dia A B 1600 ft, 6 in. dia с 2. 800 ft, 10 in. dia-
The cage system shown in the figure is made of EC rod. The Flow Limit of the material is 180 MPa and the Safety Coefficient is 4 is desired to be. Accordingly, the circular cross section EC rod Calculate the diameter.
I need the answer as soon as possible
I need the answer as soon as possible
An engineer sees a water flow through a 0.4 km long and 200 mm diameter pipe having a roughness of 0.0015 mm at 0.075 cubic meter per second. Assuming that the property of H2O is u = 0.001 Nm/sec and p = 1 g/cu.m. He is bored, so he wanted to calculate the following, help him. a. the pressure drop cause of friction b. velocity of H2O in the pipe c. find the Re?
With the line of working I underlined, please explain where that formula comes from, particularly how they are using change of length in place of delta v? Thanks
Hello please solve problem 4
Required information The figure shows a 400-mm-diameter brake drum with four internally expanding shoes. Each of the hinge pins A and B supports a pair of shoes. The actuating mechanism is to be arranged to produce the same force Fon each shoe. The face width of the shoes is 75 mm. The material used permits a coefficient of friction of 0.22 and a maximum pressure of 1000 kPa. Consider a = 0.150 m, R= 0.20 m, d= 0.050 m, and c= 0.165 m. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. 15° 15° F F 10 10 10 BY 10 FF 15° 15° Determine the following forces acting on the hinge pins of the brake. Rx1 (primary shoe) is kN. Ry1 (primary shoe) is kN. Rx2 (secondary shoe) is kN. Ry2 (secondary shoe) kN. The resultant force Ris kN.
For the configuration shown In the figure below what must be the value of the specific weight of the unknown fluld? Express your answer in Ib/ft Open Open Water 5.6in. 6.2in. 3.6in. Unknown fluid 1.Sin.
I need the answer as soon as possible