What is the total hydrostatic force on the conical stopper shown below? V cone =nr?h where r3is radius and h is the height of the cone.Atmosphere(S.G.)ig=1.2630 cm21 cm15 cm 15 cm

Name: What is the total hydrostatic force on the conical stopper shown belo
Uploaded: 2022-11-23T16:32:19.000Z
Channel: Bartleby
Description: What is the total hydrostatic force on the conical stopper shown below? V cone =nr?h where r3is radius and h is the height of the cone.Atmosphere(S.G.)ig=1.2630 cm21 cm15 cm 15 cm

please find attached solution below

Answered: What is the total hydrostatic force on…

Engineering

Civil Engineering

What is the total hydrostatic force on the conical stopper shown below? Veone = Tr²h where r is radius and h is the height of the cone. Atmosphere (S.G.)ig=1.26 | 30 cm 21 cm 15 cm 15 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The moment acting on the cross section of the beam is M� = 3 kip⋅ftkip⋅ft . (Figure 1) Determine the resultant force the bending stress produces on the top board A� of the beam. Express your answer in kilopounds to three significant figures.
A=5 B=5 C=5
A circular aluminum column 6 m long has a diameter of 200 mm. Determine the critical load if one end is recessed. E = 73 GPa. σY = 250 MPa.
Panel AB is circular and retains a liquid with specific gravity of 1.55. It has a width of 4 feet perpendicular to the paper. It has a radius of 13 feet from its center as seen in the figure. If h = 6 feet, and a = 2 feet, determine the total hydrostatic force acting on panel AB in pounds.
The cantilever beam has a rectangular cross section 50 mm wide and h mm high. Find the smallest allowable value of h if the maximum displacement of the beam is not to exceed 10 mm. Use E = 20 GPa. 4 kN 2 m 2 kN 2 m 50 mm
The 50-mm-diameter solid shaft is made of 2014-T6 aluminum and is subjected to the distributed and concentrated torsional loadings shown where T = 1.75 kN·m. (Figure 1) Part A Figure B 0.4 m T 2 kN·m/m 0.6 m 1 of 1 Determine the angle of twist at the free end A of the shaft. Express your answer in degrees to three significant figures. ΜΕ ΑΣΦ vec |= 1.89 Submit Previous Answers Request Answer × Incorrect; Try Again; 23 attempts remaining < Return to Assignment Provide Feedback ?
Asap
Determine the vertical displacement at joint (2) measured upward. Consider the truss shown in (Figure 1). Take A = 0.0015 m² and E = 200 GPa. Suppose that F = 21 kN. Express your answer to three significant figures and include the appropriate units. Enter positive value if the displacement is upward and negative value if the displacement is downward. HA ? D6 = Value Units Submit Request Answer Figure 1 of 1 Part B 2 m 2 m Determine the force in the member of the truss and state if the member is in tension or compression. 4 4 10 Express your answer to three significant figures and include the appropriate units. Enter negative value in the case of compression and positive value in the case of tension. 6 3 ? 2 m 18 95 = Value Units 5 (3 Submit Request Answer
J 6
An axial load of 900 KN is carried by a compound tube comprising of a steel tube and a brass tube. The internal and external diameter of the steel is 140 mm and 160 mm, respectively. While, the internal and external diameter of the brass tube is 160 mm and 180 mm, respectively. If the two tubes have the same length of 140mm, calculate the stresses and the load carried by each tube and the amount it shortens. Esteel = 2x10° N/mm? Ebrass = 1x10° N/mm?
4. A nylon [E = 360 ksi; v= 0.4] rod (1) having a diameter of dl = 2.50 in. is placed inside a steel [E = 29,000 ksi] tube (2) as shown in Figure P3.7. The inside diameter of the steel tube is d2 = 2.52 in. An external load P is applied to the nylon rod, compressing it. At what value of P will the space between the nylon rod and the steel tube be closed? Nylon rod (1)- Steel tube (2)
pls answer the table also