Q4/A three-phase. 60-Hz, completely transposed 345-kV, 200-km line has two 795,000-cmil 26/2 ACSR conductors per bundle and the following positive sequence line-constants: z=0.032+j0.35 Q2/km y=j4.210 S/km Full load at the receiving end of the line is 700 MW at 0.99 p.f. leading and at 95% of rated voltage. Assuming a medium-length line, determine the following: a. ABCD parameters of the nominal circuit b. Sending-end voltage VS, current IS, and real power PS c. Percent voltage regulation d. Transmission-line efficiency at full load

Q4/A three-phase. 60-Hz, completely transposed 345-kV, 200-km line has two 795,000-cmil 26/2 ACSR conductors per bundle and the following positive sequence line-constants: z=0.032+j0.35 Q2/km y=j4.210 S/km Full load at the receiving end of the line is 700 MW at 0.99 p.f. leading and at 95% of rated voltage. Assuming a medium-length line, determine the following: a. ABCD parameters of the nominal circuit b. Sending-end voltage VS, current IS, and real power PS c. Percent voltage regulation d. Transmission-line efficiency at full load

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The total conductor cross section of a 537.40 kV (Peak value) three-phase overhead line with a length of 100 km is 517 mm2 and the conductor diameter is 29.6 mm. The roughness factor of the conductors is 0.8 and the distance between the conductors is 6 m. The ambient pressure along the line is 650 mmHg and the temperature is 15oC. Since there is corona discharge in only 5 km of this line, find the total Corona loss lost to the line using the Peek equation (Ed=30kVpeak/cm for Air). I would be very happy if you could be quick. :)
A three-phase 765 kV, 60Hz, 300 km, line has the following positive sequence impedance and admittance: z=0.0165+j0.3306-0.3310<87.14° 22/km, y=j4.674x10-6 S/km. Identical shunt reactors (inductors) are connected from each phase conductor to neutral at both ends of the 300-km line during light load conditions, providing 50% compensation. The reactors are removed during heavy load conditions. Full load is 1.8 kA at unity p.f. and at 730 kV. Assuming that the sending- end voltage (Vs) is constant, determine the following: a) ABCD parameters of nominal circuit b) Sending end voltage (Vs) and current (Is) c) Percent voltage regulation of the uncompensated line d) Percent voltage regulation of the compensated line
In the medium-length power transmission line model given below, since the end-of-line voltage value of the nominal-T equivalent circuit is 154 kv, find the voltage regulation value for this line and draw the phasor diagram.
one circuit of a sinlge phase transmission line is composed of three solid 0.5 cm radius wires. the return circuit is the composed of two solid 2.5 cm radius wire . the arrangement of conductors is as shwon in figure below. applying the concept of GMD and GMR , find the inductance of the complete line in millihenry per kilometer
Q1. 30, 110 kV, 50 Hz, 150 km long transmission line consisting of three conductors each of 10 mm diameter and spaced 2-5 m apart in an equilateral triangle formation. The temperature of air is 30ºC and the atmospheric pressure is 750 mm of mercury. Take irregularity factor as 0-85. Ilonization of air may be assumed to take place at a maximum voltage gradient of 30 kV/ cm. Estimate 1. Critical disruptive voltage 2. Visual critical Voltage 3. Power loss due to corona
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1cm diameter. The conductors are arranged in a horizontal configuration with 0.71 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux link- ages, and (c) the total inductance of the line.
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
A three-phase 630 kV, 50 Hz, 400 km completely transposed long transmission line, has the following positive sequence impedance and admittance parameters. z = 0.015 + j 0.25 0/km y = j 4 x 10-6 S/km Identical shunt reactors are connected from each phase conductor to neutral at both ends of the line providing 80% compensation during light load conditions. The reactors are removed during heavy load conditions. Full load is 0.75 kA at 0.95 lagging power factor and at 600 kV. Assuming the sending end voltage remains constant. Determine the following: 1. Using the equivalent r circuit find the exact ABCD parameters of the transmission line.
12. Revi i. What difference you noticed in voltage regulation between RL and RC Loads? Why? i. Maximum voltage regulation occurs when power factor is In the case of inductive loads, for a fixed value of VR and I, the voltage regulation of the line increases with the ii. in power factor. iv, What are main reasons for voltage drop in transmission line?
Problem 1 a- Explain the meaning of the term "bundle conductor transmission line" and discuss the effects of its use on the electrical performance of a high voltage electric transmission line. b- Consider an experimental 1800 kV three phase bundle-conductor line with parameters A= 0.95 and B=j 70. Determine the value of the parameter C of the line. Assume that the line is delivering 2,000 MVA at receiving end whose voltage of 1750 kV and unity power factor. Determine the sending end voltage of the line. d- C- Determine the sending end current of the line.
If a 3-phase short circuit occurs in one of the two circuit of transmission line at point F, and the shunt impedance of the short circuit is j0.1 pu. Determine the maximum time when a short circuit can still be cleared. So=0.8+j0.3 Xd'= 0.2, XL1=XL2= 0.6, XT1=0.12, Xr2= 0.1, L1 V= 1.0 T1 L2 F T2 .XL= 0.1 Хс- 0.1. S1 S2 SL= 0.6+j0.3
please help solve this question A 100 km Three-Phase 50 Hz transposed transmission line is composed of bundle of three ACSR, 1,431,000 cmil, 47/7 Bobolink conductors as shown in Figure 2 (a). The Three-Phases (bundled Conductors) have flat horizontal spacing of 11 meters as shown in the Figure 2(a). The conductors have a diameter of 3.8 cm and a GMR of 1.5 cm. The Line is going to be replaced with a six conductor bundle of ACSR, 477,000 cmil, 26/7 Hawk conductors. The conductors have a diameter of 2.5 cm and a GMR of 0.9 cm. The new line will have a horisontal phase spacing of 14 meters as it is going to be operated at higher Voltage rating. The new line is shown in Figure 2 (b). The spacing between the bundles in Figure 2 (a) and (b) is 45 cm. Determine,a) The capacitance for each case and the percentage change in capacitanceb) The inductive reactance for each line and the percentage change.c) The inductance for each case and the percentage change ininductance