Q4// In fig shown the pipe line have (QA=15 L/s), (DA=100mm), (DD=50mm), ,(DB=DC=25mm),(QB=3QD), (uc=4m/s), Calculate the following using Sl units: 1- The velocity (U) in pipes (B): 2-The Volumetric flow rate(Q) in pipe (D). ; 3- The type of flow in pipe (A,B,C,D); 4- The mass flow rate (m.) in pipe (A,B,C,D).; note that: DA,DB, DC,DD = diameter ; kinematics viscosity 0.0001 m2/s; dynamic viscosity 0.088 kg/m.s. в A Water D

Q4// In fig shown the pipe line have (QA=15 L/s), (DA=100mm), (DD=50mm), ,(DB=DC=25mm),(QB=3QD), (uc=4m/s), Calculate the following using Sl units: 1- The velocity (U) in pipes (B): 2-The Volumetric flow rate(Q) in pipe (D). ; 3- The type of flow in pipe (A,B,C,D); 4- The mass flow rate (m.) in pipe (A,B,C,D).; note that: DA,DB, DC,DD = diameter ; kinematics viscosity 0.0001 m2/s; dynamic viscosity 0.088 kg/m.s. в A Water D

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Pls answer
16. Fluid Flow through a Compression Chamber A compressible gas flows into and out of a compression chamber as shown in Figure 9. Vin = 10 m/s Ain = 0.1 m² Pin = 3.0 kg m-3 (a) Bsys = 0 (b) bsys = dB sys dt Control Surface For the system given, which of the following statement(s) are true based on the conti- nuity equation? Be certain to justify your answer quantitatively. 0 Control Volume Figure 9: Schematic of compression chamber. (c) #0 (d) Σsbpv · A = 0 (e) & Spdv = 0 Vout = 5 m/s Aout = 0.2 m² Pout = 2.0 kg m-3 Answer(s): # 0; dB sys dt
Topic: Flow in closed conduits For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per second. Assuming all pipes have a friction factor of 0.020 Determine the head loss in feet in PIPE 2. Determine the head loss in feet in PIPE 3. Please answer with complete and detailed solution. ASAP. Thank you
A cooling fan produces air flow while consumes electrical power. The produced volumetric flow rate Q and the power consumption P depend on three variables: air density p, fan impeller diameter D, and fan angular speed o. (No need units) [1] Use dimensional analysis to find the relevant n-groups for volumetric flow rate Q and power P. (2] Predict the power consumption that would need to double (2 x) the air flow rate for a given fan (D is fixed).
I need the answer as soon as possible
For the pipe network shown below, estimate the diameter of pipe DE, knowing thatthe flow at A = 200 L/s, HA = 50 m, and HD = 20 m.
A fluid compressed in a cylinder has a volume of 1000 (1liter) at 25 MPa and a volume of 900 at 3 MPa. compute the coetficient compressiblity. Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: MPan-1 Decimal Places required in the final answer: 2
pls provide clear solns, thanks
The head loss caused in a straight pipe is O a: Minor loss Ob: No loss Oc: Major loss Od: None of these The loss in friction caused due to the bend, couplings, valves are O a: Minor loss O b: No loss Oc: Major loss Od: None of these General formula used to calculate friction loss is O a: Hazen WWilliams Ob: Bernoulli's Equation Oc: All the above O d: Darcy-Weisbach If the equivalent length of a 90' elbow is greater than the 45 elbow, the pressure loss across the 90' elbow is -------- the 45 elbow. O a: Greater than Ob: Lesser than Oc Same as O d: None of these For hydraulically smooth pipe, the resistance to flow depends only on the? O a: Relative roughness Ob: Absolute roughness Oc Reynolds number Od: Relative roughness and Reynolds number
Fluid Mechanics I need a detailed solutions and detailed drawings, thanks!
Determine the development length required for the epoxy-coated bottom bars shown in the figure. a) assuming Ktr = 0 and b) computing Ktr with the appropriate equation, fy = 420 MPa and f’c = 21 MPa.
Find pressure head, elevation head and total head for the locations A through E for the figure below. All the dimensions are given in meter (m)