GivenThe figure shows an inlet and outlet connected to a motor. If the pressure at A is6.25 MPa and the pressure at B is 3.15 MPa. The motor inlet is a steel hydraulic tubewith 25 mm OD × 1.5 mm wall and the outlet is a tube with 50 mm OD × 2.0 mmwall. The fluid is oil (sg = 0.84) and the velocity of flow is 1.40 m/s at point B.h1 = 2.60 mRequiredCalculate the power delivered to the hydraulic motor in kW to the nearest 100th.Ah1Flow|Motor

The figure shows an inlet and outlet connected to a motor. If the pressure at A is 6.25 MPa and the pressure at B is 3.15 MPa. The motor inlet is a steel hydraulic tube with 25 mm OD x 1.5 mm wall and the outlet is a tube with 50 mm OD x 2.0 mm wall. The fluid is oil (sg = 0.84) and the velocity of flow is 1.40 m/s at point B. h1 = 2.60 m Required Calculate the power delivered to the hydraulic motor in kW to the nearest 100th.

The figure shows an inlet and outlet connected to a motor. If the pressure at A is 6.25 MPa and the pressure at B is 3.15 MPa. The motor inlet is a steel hydraulic tube with 25 mm OD x 1.5 mm wall and the outlet is a tube with 50 mm OD x 2.0 mm wall. The fluid is oil (sg = 0.84) and the velocity of flow is 1.40 m/s at point B. h1 = 2.60 m Required Calculate the power delivered to the hydraulic motor in kW to the nearest 100th.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows a portion of a hydraulic circuit. The pressure at point B must be 250psig. When the volume of flow rate is 80gal/min. The hydraulic fluid has a specific gravity of 0.90 and a dynamic viscosity of 6.00 X 10-5 lb.s/ft2. The total length of the pipe between A and B is 25ft. The elbows are standards. Calculate the pressure at the outlet of the pump at A.
2. A tank and piping system are shown below. The total length of PVC pipe is 2500 ft and discharges water into the atmosphere. The pipeline has an open globe valve and four threaded elbows; h1 = 10 ft and h2 = 45 ft." a. If the discharge is 0.5 cfs, what NPS should be used for the PVC pipe (ks = 0.00006 inch). b. What is the pressure at A, the midpoint of the pipeline? c. Draw the EGL and HGL. h2 Water T = 10°C (50°F) Globe valve
Choose one: 3 kPa 0 kPa 12 kPa 6 kPa
Subject : Fluid mechanics Please give me both right solutions
A cylinder is placed in a steady water flow as shown. Calculate the pressure difference PB - PA in psi if the flow speed at A is 10 ft/sec. .A O 1.04 O 1.53 0.67 1.92 0.82 O 1.74
Please see pic
b2
Q1 Given is a three-pipe series system, as in Fig. The total pressure drop is py — ps = 150,000 Pa, and the elevation drop is z4 — 25 = 5 m. The pipe data are Pipe L.om d, em e mm eld 1 100 8 024 0.003 2 150 6 0.12 0.002 3 80 4 0.20 0.005 The fluid is water, p = 1000 kg/m’ and v = 1.02 X 10~° m%s. Calculate the flow rate Q in mh through the system. o © 0O Al — —_— — B T U
Water flows from a pressurized tank, through a valve and out a pipe. If Q= 0.1 ft/s, Az 10 ft, P2=0 psig, D = 1lin., ht 5V/2g, please answer the following questions: 1) the pressure in the tank in psig, 2) sketch the EGL of the system., 3) sketch the HGL of the system Air under pressure Water Partly open valve Figure 3. A water tank discharges water through a partly open valve in a pipe with a diameter d
For this diagram of an industrial pressure washer system, x = 2 ft, y = 5 ft, z = 9 ft, Q = 3.4 ft3/s, and the hose diameter is 3 in. Assuming a head loss of 4 ft is derived over the distance from point 2 to the jet, what is the pressure at point 2 if the jet from the nozzle is 1 in. in diameter? Assume a = 1.0 throughout. O 535164 psi O 372383 psi O 2586 psi ○ 4996 psi 2 Z Nozzle
A fluid is flowing in a pipe 20-cm∅ with a mean velocity of 3 m/s. The pressure at the center of the is 35 kPa and the elevation of the pipe above the assumed datum is 5 m. compute the total head, E in meters, if the fluid is:a) Oil (sp.gr. = 0.85)b) Gas (γ = 6.30 N/m3) c) Water Pls include figure for better understanding
Give me right solution urgent please