Question 3: The following system is used to drive water from the left tank to the right tank. The pipes are made of plastic. ( ›) a. Calculate the flow rate of water (. b. Calculate pressure loss through the tubes c. Calculate minor pressure losses (

Q: Question 1 a) List out 3 devices to measure hydrostatic pressure. Explain how U-tube manometer can…

A: Hydrostatic pressure- It is defined as the pressure in which exerted by a fluid at rest due to the…

Q: A large tank open to the atmosphere is filled with water to a height of 9.3 m from the outlet tap. A…

A: Discharge through the mouth piece= Q=Cd a2gH Velocity = Q/a= Cd2gH= 0.7072*9.81*9.3= 9.55 m/s So the…

Q: the discharge coefficient of a Venturi .... meter has a value ............ 0.6 0.92 to 0.99 venturi…

A: Venturi meter- Venturi meter is a type of flowmeter that works on the principle of Bernoulli’s…

Q: Please define your CV for each problem. 1) A cylindrical tank (of inner diameter D and mass m,)…

A: The volume of fluid flowing through a given area of a cross-sectional area per unit time is called…

Q: •.. 300 mm H20 150 mmg 425mm CHg C13-6) A 150mm diameter venturi meter is installed in a 300mm…

A: Given data, Dia of pipe, d1=300 mm=0.3 mdia of throat, d2=150 mm=0.15 mmercury differential,x=425…

Q: Refer to the parallel piping as shown. The water is flowing at Q = 0.03 m³/s. Pipe 1 has a diameter…

A: The given data is shown below: Q=0.03 m3/sDiameter of pipe 1=100 mmDiameter of pipe 2=50 mm

Q: 7. When the fluid flow is discontinuous, what is established?

A: To find : If fluid flow will be discontinuous then what is established.

Q: lution so i c

A: Apply Bernoullis theorem P1γw+v122g+z1=P2γw+v222g+z2we knowP1=P2=Patm=0v1=0  (as large dia)

Q: Calculate the pressure at B.

A:

Q: An open cylindrical tank contains two liquids with a specific gravities and depths as follows:…

A: Liquid 1 Specific gravity, S1 = 1.02 Depth, H1 =1.12m Liquid 2 Specific gravity, S2 = 1.02 Depth, H2…

Q: 14.5 A differential gauge was attached to a inches. Assume no headloss. Point B is located at the 6…

A: From the given question it is required to calculate the flow rate in ft3/s.

Q: For the pipe network shown below, estimate the diameter of pipe DE, knowing that the flow at A = 200…

A: Data given Find : Diameter of pipe ED

Q: c) For the system shown in Figure 3.1, calculate (i) the volume flow rate of water from the nozzle…

A: (a) Expression of Bernoulli equation for section C and B as; PCγ+v2c2g+zc=PBγ+v2B2g+zB       ......1…

Q: Determine the diameter of the nozzle, if the flowing fluid in the nozzle has a specific gravity of…

A: To Determine Diameter of the nozzle, D

Q: Problem 2 :Air flows steadily between two cross sections in a straight pipe of cross-sectional area…

A: The values and figure given in the question are as follows: Pressure at section-1 (P1)=300 kPa…

Q: Tow oil tanks are connected with a pip that has a constant radius, the readings of the two gauges…

A: Given data in question  Pressure at point 1 and 2 Elevation head at point 1 and 2 Specific gravity…

Q: For the system shown in the figure below, find the discharge in each pipe v-1.003-10 m³/s; 7-9810…

A: We know that friction factor is given by ; 1F = 2 log10 Re + 1.74 - For Pipe 1 : 1F1 = 2 log10 Re +…

Q: Question 3: Find the flow if the two pipes are made of PVC. 7m 4m 5 cm 3 m 8 cm 5 m

A: Given data in question Height of reserviors 7 and 5 mLengths 4 and 3 mDiameter 5 and 8 cmPVC pipesTo…

Q: *1-8. The bottle tank has a volume of 1.12 m³ and contains oxygen at an absolute pressure of 12 MPa…

A:

Q: Elevation 15.25m Elevation 14 m water Elevation 10.7m 30° An orifice in a 30 degree plane from…

A:

Q: Describe about the Water in Capillary Tubes.

A: Capillary action happens because the effects of cohesion and adhesion make water sticky.

Q: Given: Water flows through a nozzle, at section 2, the nozzle discharges to atmosphere. 2 10 V Find:…

A:

Q: A pipe has a uniform diameter of 750 mm. The flow rate entering the pipe is 2.21 m^3/s. The exit…

A:

Q: A 50 °C of liquid water is flowing into and discharging from a pipe U-section as shown in Figure 1.…

A: Velocity defines how fast the air is moving in distance per unit of time. The common units are…

Q: Urgent, need correct answer as soon as possible with complete solution. Box final answer in 4…

A: Diameter=10mm

Q: Water exits a pipe as a free jet and flows to a height "h" above the exit plane. The flow is steady,…

A:

Q: Oricul Q3: Three pipes (A, B and C) are interconnected as shown in figure (3). Determine the flow…

A:

Q: FOR THE PIPE SYSTEM SHOWN FIND THE total headloss IF Q = 1.3m3/s. LET DIAMETERS BE 200mm, 250mm, and…

A:

Q: A 600m long pipe with a diameter of 600mm has a headloss of 1.20m. Detemine the following: a.)…

A: Given data- Length of pipe (L) = 600 m Dia of pipe (D) =600 mm = 0.6 m Headloss (hf) = 1.20 m

Q: URGENT Please answer this problem in 30minutes. I need correct answers with complete and step by…

A:

Q: Draw the EGL and HGL for the following system.

A: The flow of fluid includes movement of an unbalanced fluid. As long as unequaled forces are in…

Q: he proper-sized steel tube for a flow rate of 20 gpm and an operating pressure of 1.000 psi. The…

A: Solution-  Data given   flow rate = 20 gpm operating pressure = 1000 psi    velocity = 20 ft/s…

Q: Q5= The compartments (8) 4. in tigure below are closed & filled with air. When the gauges (A) (D)…

A: GIVEN: PA=2.07 bar=2.07×100000=207000 Pa specific weight (γm)=13.6×9810 N/m3 =133416 N/m3

Q: Find the head of internal mouthpiece (running fulI), a diameter and discharge of the mouthpiece are…

A: Given: Diameter, d = 150 mm = 0.15 m Discharge, Q = 32 litre/s = 0.032 m3/s

Q: 4m Oil (0.90) 3.75 mm Mercury (13.57) This vertical pipeline with attached gage and manometer…

A: Given data in question  Vertical pipe Specific gravity  Mercury To find out  Pressure at A in bars

Q: Determine the discharge, HGL, and EGL. Water 20°C 4-cm-dia. wrought iron pipe 20 m Screwed elbows 40…

A:

Q: For the system in the figure, calculate the distancevertical between the surfaces of the two…

A: Step 1:QStep 2: Step 3: Step 4:

Pressurized pipe flow

A 15-kilometer-long pipe with a pipe diameter of one meter transports water at a speed of one meter per second. The pipe has a friction coefficient of 0.005. Calculate the frictional head loss?