Q5: The compartments (B) 4 Cc) in figure below are closed& filled with air. When the gauges (A) f (D) read asindicated, what should be the value of Cx) for gaug eCE)?(Mercury in each U-tube gauge)2.07 barB254AirDAirE

GIVEN: PA=2.07 bar=2.07×100000=207000 Pa specific weight (γm)=13.6×9810 N/m3 =133416 N/m3

Answered: Q5= The compartments (8) 4. in tigure…

Q5= The compartments (8) 4. in tigure below are closed & filled with air. When the gauges (A) (D) read as indicated, what should be the value of Cx) for gaugeCE)? (Mercury in each U-tube gauge)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An alumunam tod 2 2 cm diameter is serewed at the ends, and passes through a sterl tube 25 em anternal diameter and 03 cm thik Both are heatecd to a temperature of 140 C, when the nuts on the rod are serewed laghtly on to the ends af the tube Estumate the stress ir the sod when the commor temperature has fallen to 20 C For steel, E for alumanum, E 20GN m and a 23 10 per , where f is Yaung's madulus and a is the coetficient of linear expansaon 200 GN m anda 12 10 per C, and
4.3 bar (gauge) equle to ..... ... الجواب
Ex/Determine the reaction TIT 4m LUCL B Um A is Fixed 2m 2 KN 2m WWW um C use (Force method) , B and c rod E = 200 GPa 4 I = 400 mm A = 2.5mm
A (A) 9 (B) 10 C) 14 (D) 13 ←N→ B 40 kips 1.5" 40 kips с -22 kips 22 kips D 20 kips From the figure, if 7/8" diameter bolts are connecting the rod at A, determine the minimum number of bolts required if the allowable stress for each bolt is 10ksi.
In Fipure , with its dimensions, loadinp Status and material properties,different full circle cross -sec¥ion rod has been piven. The AB part Of the rod is steel, 100mm in diameter; BE part is COpper and i diameter. It Is 80 mm - Draw the Force Diaprom Of the Bar Calculate +he Normol stresses that will occur in parts AB and BC. Calcu late the total lenpht chanpe of the rodi 179 86 Material ECM Pa) (Copper) steel 210000 (steel) Copper 100000 120 cm 110cm
The bar shown, made from machined steel (S, = 693 MPa. Su = 769 MPa). is subjected to a fully reversed bending moment of 20 N.m. Calculate the corrected endurance limit for a 50% reliability. The bar will be used at a temperature of 500 °C. 30 mm 10 mm 1,5 mm 5 mm M M 1.5 mm Select one: O a. Se = 147.14 MPa O b. Se = 169.59 MPa O c.Se = 191.03 MPa O d. Se = 211.62 MPa %3D
Please answer with a complete solution. Including the given, what's required, and the solution with FBD. Thank you!
The bolts used for connecting the angle shown in the figure are 22mm in diameter. The thickness of the angle is 8mm. Use F, = 145 MPa F = 230 MPa Determine the safe load P. 80 60 120 60 68 115 68 120 120 109 -8-
water 3cm D=5 cm Mereury The tank in the has a 5 cm diameter plug at the bottom.on the rrght. All fluids are at zóc The Plag will pup out if the hydrestatic force is 30 for this condition what will be the readineg h ont Meicury mahometer on the left side2
B1
Quiz-3: (Optional) Find the stresses which may induced in each rod if temperature is increases by 70°C. Aluminum Bronze 1.2m 6mm, Im AA-20 Cm² Ав15 Сm? ɑAi-23*106 m/m.°C ɑB=18*10-6 m/m.°C EA-70GPA Ев 80GPa
The A-36 steel pipe has an outer radius of 20 mm and an inner radius of 15 mm. If it fits snugly between the fixed walls before it is loaded, determine the reaction at the walls when it is subjected to the load shown. B A 8 kN -8 kN 700 mm |- 300 mm-