Q3. The attachment shown in Fig.2 is made of 1040 HR. Design the weldment(give the pattern, electrode number, type of weld, length of weld, and leg size).All dimensions inmm120Fig.21217b =7.55 kN6060°

Step 1: Understanding the Problem and Forces Acting on the Weld In this step, we analyze the given…

Answered: Q3. The attachment shown in Fig.2 is…

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter25: Testing And Inspection

Section: Chapter Questions

Problem 24R: What would be the transverse shear strength per inch of weld if a specimen that was 2.5 in. wide...

See similar textbooks

Similar questions

The value for the area is correct please answer the remaining 2 problems!! Thanks!
I want a human solution
8. Design the length of weld (L) in the connection below to develop the full tensile capacity of the plate. Use E70 electrodes and 1/4" side fillet welds. The material is ASTM A36 Steel and the allowable axial tensile stress is 22,000 psi. (show all your work) "L" PL 1/2" PL 3/8" x 6" P
O wrapping the weld around the corner a minuimum of the specified weld size and ar wrapping the weld around the corner for a distance not less than two times nor mor QUESTION 4 On all CJP groove welds in butt joints transverse to the computed tensile stress, they:. O A. Shall have no visible porosity that exceeds 1/32" O B. shall have no visible porosity that exceeds 3/32" O C. shall have no visible porosity O D. shall not have a sum of visible porosity that exceeds 3/8" O E. shall not have a sum of visible porosity that exceeds 1/2" QUESTION 5
Q2: Two plates, 25 mm thick, are welded together by means of trans verse-fillet welds. The ultimate tensile strength of a weld metal is 415 MPa. The surface finish factor of the weld surface is 0.5, and the size factor is 0.85. The reliability is 90%. Determine the length of the weld if the factor of safety is 2. The transverse force on the welds is 100 kN, which is completely reversed under fatigue loading. Take: A=10mm 25 A Toe
Question: a) A plate 100 mm wide and 10 mm thick is to be welded to another plate by means of double parallel fillets. The plates are subjected to a static load of 80 kN. Find the length of weld if the permissible shear stress in the weld does not exceed 55MPa. Determine the increase in load carrying capacity if a combination of single transverse double parallel fillet is used the permissible tensile strength of material is 80MPa. b) Draw a neat sketch of double riveted double cover but joint. If 8mm plates with 20 mm diameter rivets having a pitch of 50 mm are joint using double riveted lap joint. The permissible stresses are permissible tensile stress = 120 MPa;Permissible crushing stress= 100 MPa; Permissble shear stess= 150 MPa. Find the strengths and efficiency of joint, taking the strength of the rivet in double shear acoording to the indian boiler standards.
USE IMAGE BELOW And Give your answer in in^4
2. A circular steel bar (50 mm) diameter and (200 mm) long is welded perpendicularly to a steel plate to form a cantilever to be loaded with (5 kN)at the free end. Determine the size of the weld, assuming the allowable stress in the weld as (100 MPa). [Ans. 7.2 mm]
design of machine elements solve according to R.S. Khurmi, J.K.
Join two pieces of metal that are .045 and .045 thick. The joint is made with a triple row of MS20426 rivets. Use minimum edge distance and spacing. The Joint is 7 inches. Diameter of rivets = Length of rivets = Rivet Part Number = Number of rivets =
The allowable unit stress in shear on a fillet weld is 13,600 psi, and the total actual length of the weld cannot exceed 3 in. If the weld must transmit a total force equal to 9600 lb, it’s size should be A. 1/2 in. B. 3/8 in. C. 5/16 in. D. 1/4 in.
7) For double side parallel fillet weld subjected to an external force 100 kN. The weld has throat thickness of 5 mm and the measured shear stress is found to be 100 MPa. From the above given information find out the length of the welded joint desigN? O 100 mm 50 mm 25 mm 10 mm

SEE MORE QUESTIONS

Recommended textbooks for you

Welding: Principles and Applications (MindTap Cou…

Mechanical Engineering

ISBN:

9781305494695

Author:

Larry Jeffus

Publisher:

Cengage Learning