Join two pieces of metal that are .045 and .045 thick. The joint is made with a triple row of MS20426 rivets. Use minimum edge distance and spacing. The Joint is 7 inches. Diameter of rivets = Length of rivets = Rivet Part Number =

Q: Q-The lap distance in different types of bonding is equal to the horizontal distance between two…

A: The lap distance in various kinds of bonding is the horizontal distance measured between two perpend…

Q: Q4: Determine the plate thickness if the rivet diameter was 10 mm?

A:

Q: The block has a mass of 4.5 kg and rests on the smooth plane as shown in . Part A k = 200 N/m 500000…

A:

Q: In order for a certain refrigerator door to close tightly, the refrigerator must beleveled up 0.24…

A: Given data as per question Total thickness = 0.24 in The thickness of lower shim =0.097 in

Q: In determining the net cross sectional area of a structural steel tension member, the diameter of a…

A:

Q: If 4 lengths of support brace are required for a job, 34 13" and 45 57 1", what is the total length…

A: Given Data⇒ Lengths of subparts is : L1=341316''L2=4578''L3=291516''L4=5714''

Q: 4. Design a welded connection to resist the loading shown below (service load). A double angle…

A: DL=30 k,LL=75 k,Wn=1.2×30+1.6×75Wn=156 kipsLoad on each angle=1562=78 kips=PAngle section…

Q: Dynamic forces F1 = 4000N and F2 = 6000N are applied to the welded part shown in the figure as shown…

A:

Q: An open cylindrical tank E mm in diameter and made of F mm thick plate is subjected to an internal…

A: According to the given information we have a diameter of the cylinder is 6 mm. the thickness of the…

Q: Q2/ Determine the diameter of the rivets and the forces in all rivets. Take Tallowable as 60 MN/mm2.

A:

Q: R L2 (Side view) (End view)

A: Given data: α (Bend angle) =70° Kba (Strecth factor) =0.33  t  (Stock thickness) = 0.3" R (Width…

Q: Determine the y-coordinate of the centroid. 30 mm C -80 mm 30 mm x' a

A:

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Draw the Welding symbol based on the data given • SINGLE BEVEL BUTT WELD • Flat FACE • SIZE 45 mm •…

A: Given data  SINGLE BEVEL BUTT WELD Flat FACE SIZE 45 mm HIDDEN SIDE ALL AROUND WELD To Draw the…

Q: Q1) Prepare cross-sectional views of the following fillet weld and redraw the joints representing…

A: (i) Draw the cross sectional view.

Q: 10. Sketch the welding symbol that indicates the joint preparation and other elements required for…

A: Welding is fabrication process that joints meterials usually metals, thermoplastics by using high…

Q: Note: the drawing below shows the end view of a weldment consisting of 7 tubes. 8.625" 4. What is…

A: It is required to determine c to c distance

Q: The steel wide-flange beam has the dimensions shown. If it is made of an elastic perfectly plastic…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: The type of joint used in wooden photo frarnes is O A. Mitre joint

A: Ans-A. Miter joint.

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: Draw the weld symbol for the following welded joint in Figure 1. 6 09 (a) 6 (b) (c) Figure 1 6

A:

Q: 15 What is the weight of the weldment shown? (MS) Plate= .2835 lbs. per cubic inch. V 58" x 21 x 21"…

A:

Q: On all CJP groove welds in butt joints transverse to the computed tensile stress, they: O A. Shall…

A: Introduction The Complete Joint Penetration (CJP) groove weld is a groove weld that extends…

Q: a)Consider the cable supporting the hook, and thus the load.  The magnitude of the internal force…

A: Given: To Find: a) Consider the cable supporting the hook, and thus the load.  The magnitude of the…

Q: I NEED THE ANSWER ASAP. I WILL GIVE YOU A TIP ON PAYPAL IF YOU HELP ME SUBMIT AS EARLY AS POSSIBLE.…

A: Longitudinal Stress

Q: What is the worst-case distance between the bottom surface of the slot and the bottom surface of the…

A: Worst case between the bottom surface of the slot and the bottom surface of the part is the…

Q: If the taper angle, large diameter, smaller diameters are respectively 2°, 44 mm, and 34mm. Find the…

A:

Q: Determine the diameter of the stud bolt that are required to fasten down the cylinder head of a 203…

A: Given Data- Area of cylinder A= 203×304mm2=2πrh Explosion pressure P= 31kg/cm2 Material SAE1020 from…

Q: Draw a welding symbol from the following information DOUBLE BEVEL BUTTWELD JOINT CONCAVE FACE SIZE…

A: Solution:   The weld symbol is shown below:

Q: Determine the rivet diameter to join the plate with thickness 20 mm

A: Given thickness =20 mm  assuming  loading acting=  P Bearing pressure =σb Diameter of plate =d

Q: Straight gibs are adjusted by screws spaced out along the length of the gib.   Select one: True…

A:

Q: Engineer Robin wants to haul a certain piece of steel barbell for his superhero training. The…

A: First we will determine the total volume of a steel barbell. V=π4d2h+π4d2h+π4D2H…

Q: Find the information from the following weld symbol. 20 2.

A:

Q: A metal cutter is used to chop metal sheets. The length of the metal sheets is 100 width of the…

A:

Q: 140 N 80 30 26 mm 39 mm 1. Find the magnitude of force "F" and, 2. the magnitude of the pin-joint…

A: