15 What is the weight of the weldment shown? (MS) Plate= .2835 lbs. per cubic inch. V 58" x 21 x 21" M.S. plate both ends 5/8=-625 W16 x 26 x 1412 @26 lbs. f a. b. 241.90 lbs 533.28 lbs C. 206.45 lbs d. 455.14 lbs 7

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: If the 45 degree offset distance at point B is 8 inches, the "travel" distance (center to center)…

A: It is given that the offset is 45 degrees and it is needed to determine the center to center…

Q: In determining the net cross sectional area of a structural steel tension member, the diameter of a…

A:

Q: What is the maximum magnitude of the bending moment caused by force G? If none, enter zero. Do not…

A: It is required to determine the magnitude of the maximum bending moment by the force G.

Q: a) Determine the second moment of area (IXX) about the centroidal x-axis for the solid homogeneous…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on both…

A:

Q: A) Draw a Free Body Diagram of the ABC bar. B) Draw a Free Body Diagram of the CDE piece. C)…

A: According to the details provided in the question, we need to find  F.B.D. of the ABC and CDE part…

Q: The distance y from the back of the shorter leg to the neutral axis XX is

A:

Q: the given area of 10 cm 2, the moment of inertia about axis 1 is 708 cm4. When d1 = d2 = 2 cm,  the…

A:

Q: 0.75' C 4.5' Z 21-4 D A a 2 0.5' 2.5' B 10.5 X

A: (a) 2z ft(b) 0.5x+0.5y ft(c) -4.5x+0.75y+2.5z(d) -3.9x+y(e) 0.5x+0.5y-2z(f) 0.6x+0.25y-2.5z(g)…

Q: For the shape below, calculate the second moment of area (moment of intertia) with respect to the…

A: Moment of area about x axis is 0.27*10-3 m4Explanation:Please find solution

Q: Write the equation of the Centroid of an area?

A: The centroid of an area is the center of gravity of that particular area where the entire mass can…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. Hint: Do…

A: It is asked to find the volume of the model based on the given dimensions

Q: 0.250 DRILL THRU SIX HOLES EQUALLY SPACED 23° 30° CYLINDRICAL PLATE 1" STD 8 PIPE 3" XS BI PIPE 3"…

A: Section A-A represents the following thing.

Q: Find the Centroid of the composite area shown below.

A:

Q: What are the forces cx and cy? Force F = 150

A: Given data F=150lb

Q: a) Calculate the area of the plate. A= Number in?

A: Given:

Q: A B Cell 1 Cell 2 с D Figure 1. A double-cell thin-walled section of a fuselage. Table 1. Geometric…

A:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: Assignment Find the centre of area (centroid) of the following figures. 4 in.- 5 in. in. 2 in. -1…

A: Dear student,                     According to the guidelines I am allowed to answer only one…

Q: You want to upgrade the tires on your truck. The manufacturer tires are P160/70R14. You want to…

A:

Q: a) A simply supported beam has a symmetrical rectangular cross-section. If the second moment of area…

A: Given: The inertia of the rectangular section is, I=11.50×106 mm4. The depth of the rectangular…

Q: I need help answering this.

A: 1)  Only one angular dimension is shown on this print  .i.e., 16002) Two  reference dimensions are…

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.