Required information Two portions of member AB are glued together along a plane forming an angle 0 with the horizontal. The ultimate stress for the glued joint is 2.7 ksi in tension and 1.8 ksi in shear. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A 2.4 kips ---- 1.25 in. 2.0 in. Determine the value of 0 for which the factor of safety of the member is maximum. (Hint: Equate the expressions obtained for the factors of safety with respect to the normal and shearing stresses.) The value of 0 for which the factor of safety of the member is maximum is

Q: How much machining tin 58 mm over a length of approach length and ow

A: Machining Time

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: What is the tool length offset? How is the tool length offset measured

A:

Q: the reading of this tool is

A:

Q: dentify the side rake angle (in degrees), from the following single point  tool signature…

A:

Q: The rotatory speed of the cutting tool and the feed rate of the workpiece depend upon the type of…

A:

Q: For a drilling operations, the feed per revolution is 0.08 mm / rev and the spindle speed is…

A:

Q: Figure and table given  below shows the design details of a taper turning operation with a cutting…

A: Given data: The cutting speed of the tool is v=22 mmin The feed of the tool is f=0.2 mmrev The depth…

Q: 3. (a) In the set-up shown, if the support columns are removed, what will happen to the see-saw?…

A:

Q: D d a° L1 SI. Parameter in Dimension in No: Drawing mm 1 d 35 2 L1 28 Cutting speed (Cs) in m/…

A:

Q: The surface finish specification in a turning job is 0.90 um. The work material is cast iron. The…

A:

Q: 4. Name 4 types of cutting tool wears and explain what problem can happen if the depth of cut is…

A: Tool wear : It is breakdown and gradual failure of  cutting tool due to regular operation on…

Q: How does taper turning process differ from turning process?

A: First of all, we know about that  Taper Turning process The process of uniformly reducing the…

Q: Read the sentences given below and Identify the wrong statement.   Sentence 1. The advantage of an…

A: Independent chuck works as the holding device for the workpiece. It contains 4 independent jaws that…

Q: How are center holes drilled after layout ? Show the diagram of a method

A: When work is held and turned between centers, a center hole is required on each end of the work. It…

Q: 17, 18, 19, 20. A gear wheel of 34 teeth has to be milled by simple indexing n each tooth, the index…

A:

Q: Would a 0.010" or 0.031" tool nose radius be stronger

A:

Q: Lathe operations and processes What is a single point cutting tool? What are the angles to which the…

A: 1)  Lathe Operations: Step Turning: Reduction of diameter.  Taper Turning: To produce tapered…

Q: ample: calculate the

A: given:

Q: Find the cutting speed in meter/minute for a step milling operation by 22mm end mill with a spindle…

A: Given data  spindle speed (N) = 260 rpm end mill dia (d) = 22 mm = 0.022 m    To determine  Cutting…

Q: proper Cutting and feed being ant? o we Set the tool just piece center-line h1 mm depth of cut ece…

A: 1 cutting speed and feed is very important parameters in metal removal process because a) it…

Q: (8 10 6, 11 22 23 24 2 25 12 13 (6 (14.

A: given: name the part of lathe machine?

Q: Knurling operation is done for )1 نقطة( Sizing purpose Cutting purpose O Gripping purpose

A: Option C is correct.

Q: Identify the side relief angle (in degrees) from the following single point tool signature 1-…

A:

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: 4. The drilling speed for cast iron is assumed to be 70 ft/min. Find the time required to drill two…

A:

Q: What is the stroke per minute of a mild steel which cutting speed is 200 fpm having a total length…

A:

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.