Q3: The rigid beam shown in Fig. 4- 19a is fixed to the top of the three posts made of A-36 steel and 2014-T6 aluminum. Compute the axial strain for each post, and the lateral strain, if (V=0.4 for steel, and V=0.25 for aluminum). --300 mm---300 mm -150 kN/m 60 mm- 40 mm H Steel 40 mm- Aluminum Steel 250 mm

Q3: The rigid beam shown in Fig. 4- 19a is fixed to the top of the three posts made of A-36 steel and 2014-T6 aluminum. Compute the axial strain for each post, and the lateral strain, if (V=0.4 for steel, and V=0.25 for aluminum). --300 mm---300 mm -150 kN/m 60 mm- 40 mm H Steel 40 mm- Aluminum Steel 250 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem 01.054-Analysis of an inverted T-frame In the steel structure shown, a 6-mm-diameter pin is used at C and 12-mm-diameter pins are used at B and D. The ultimate shearin stress is 150 MPa at all connections, and the ultimate normal stress is 340 MPa in link BD. Knowing that a factor of safety of 3.0 is desired, determine the largest load P that can be applied at A. Note that link BD is not reinforced around the pin holes. Front view. 160 mm D B 18 mm B Top view 120 mm largest load P that can be applied at A is 99252 2.328 KN. ED 6 mm 22B Side view
Two vertical forces are applied to a beam of the cross section shown in Fig.2. Determine the maximum tensile and compressive stresses in portion BC of the beam.(Take R=h=25mm). 4 kN 4KN -le A What B 300 mm 300 mm
The light rigid bar ABCD as shown is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the allowable load P if the stresses are not to exceed 60 MPa and 150 MPa in the aluminium and steel, respectively.
QUESTION 2 The C83400-red-brass rod AB and 2014-T6- aluminum rod BC are joined at the collar B and fixed connected at their ends If there is no load in the members when T1 = 50'F, determine the average normal stress in each member when T2 = 120°F Also, how far will the collar be displaced? The cross-sectional area of each member is 1.75 in? 3 ft 2 ft
A steel column is pin connected at the top and bottom which is laterally braced and subjected to transverse loading. It carries an axial load of 800 kN and a 70 kN-m moment. Use ASD. The steel section has the following properties: A = 13000 mm² r = 94 mm Ix = 300 x 106 mm4 Sx = 1200 x 103 mm³ L = 3.6 m Yield stress Fy = 248 MPa Axial compressive stress that would be permitted if axial force alone existed, Fa = 115 MPa Compressive bending stress that would be permitted if bending moment alone existed, Fb = 148 MPa Members subjected to both axial compression and bending stresses shall be proportioned to satisfy the following requirements: Mry + 9 Mex Mey Determine the axial compressive stress if axial load only existed. Pr 8 Mrx + Pe 75.82 MPa 61.54 MPa 33.96 MPa 16.25 MPa Determine the bending stress if bending moment alone existed. 76.25 MPa O58.33 MPa 13.33 MPa ≤ 1.0 16.59 MPa Determine the value of both axial and bending moment interaction value, considering the amplification due to…
The three suspender bars are made of A992 steel and have equal cross-sectional areas of 450 mm2. Determine the average normal stress in each bar if the rigid beam is subjected to the loading shown. Use E = 200 GPa B 60 kN 2 m 40 kN E F1m--1m--1 m--1m-
Direct Stress Bronze Aluminum Steel A = 0.75 in.2 A = 1.0 in.? A = 0.5 in.? 3P 2F P 4P- -3 ft→ 5 ft 4 ft- 2. Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. Find the largest safe value of P if the working stresses are 120 MPa for steel, 68 MPa for aluminum, and 110 MPa for bronze.
2-A steel rod having a cross-sectional area of 324 mm2 and is 10 m long .The rod is loading by tensile force (31 kN) and the total ngation * (Delta*L) is not to exceed 5.3 mm. the tensile strain is
A cast iron beam is of I– section as shown in Figure (3). The beam is simply supported on a span of 5 m. If the tensile stress is not to exceed 20 N/mm2, find the safe uniformly load which the beam can carry. Find also the maximum compressive stress. -80 mm- 20 mm 169.34 mm 200 mm 20 mm N 90.66 mm 40 mm 160 mm Figure (3)
6- For a simply supported beam with b=300 mm and d=500 mm, if f = 63MPa, f, = 280 MPa and the net tensile strain is greater than 0.005, then the maximum steel ratio equal............ (a) 0.0406 (b) 0.0310 (c) 0.0287 (d) 0.0180 (e) None
Question 15 The design shear resistance, Vpl.Rd of a fully restrained simply supported Universal Beam with yield strength 345 N/mm² is 1,285 kN A point load of magnitude 1,906 kN is applied at the beam's mid-span The area of the web of the beam is Aw = 5,505 mm² The plastic modulus is Wpl.y = 2,979 cm³ The thickness of the beam web is tw = 12.6 mm Find the reduced design moment of resistance of the beam Mc,Rd (use the formula for l-cross-sections with equal flanges and bending about the major axis) Give your answer in kNm to the nearest whole number. Do not include units in your answer.
A flexural member is fabricated from two flange plates 1/2x16 and a web plate 1/4x20, thusforming a built-up ‘I’ shape member. The yield stress of the steel is 50 ksi.a. Compute the plastic section modulus Z and the plastic moment Mp with respect to the majoraxis.b. Compute the section modulus S and the plastic moment My with respect to the major axis