Q1/ From the Figure below, calculate the height of the building if the distances AB=5m, DD1=1.2m andBT=25m?Rodsline of sight25 mE1.5 mBuildingA 5m BQ2/ Describe how would you find the suitable scale of the map to draw the plan of drawing havingdimensions (10 *20)m on the sheet drawing with dimensions (210 * 290) mm.

"Since you have posted multiple questions. we will solve first for you. To get the remaining…

Answered: Q1/ From the Figure below, calculate…

Q1/ From the Figure below, calculate the height of the building if the distances AB=5m, DD1=1.2m and BT=25m? B A▶▶5m B Rods line of sight 25 m E 1.5 m Building

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: of the corner cuts are as indicated on the sketch. Determine the total volume in cu. m. Round off…

Q: Sta. B.S. H.I. F.S. Elevation В.М. 1 1.21 50.00 Т.Р. 1 6.20 4.65 Т.Р. 2 4.82 3.11 Т.Р. 3 3.03 5.22…

A: Height of Instrument= Elevation+BS Elevation=Height of instrument-FS STATION B.S. H.I F.S.…

Q: Find dimension B as shown in the figure below. Round answer to the nearest tenth. 425.0 260.00…

A: The Concept of Similar triangle has been used here. Two triangles are said to be similar if their…

Q: Question. Calculate the total correction (m) required, if a line measured using 20 m chain is 2380…

A: given measured distance=2380 mactual length of tape=20.2 mnominal length of tape=20 m

Q: 1. Complete the differential level notes shown below, perform the customary arithmetic check,…

A: Leveling is the process in which we measure the levels of the various point of field in a linear or…

Q: ht of material in in situ sta nt of material submerge ir sity 0.4DD %3D naterialhas a diameter of

Q: An engineer's chain was used to measure a line, there were 6 tallies recorded, the rear chairman had…

Q: For the following notes, the base is 24 ft. C6.4 43.6 12 + 90 12 + 30 C3.1 30.4 C3.6 0 C4.9 0 C5.7…

A: Base, b = 24 ft12+90C6.4C3.6C5.743.6040.812+30C3.1C4.9C4.330.4035.2

Q: 3. Transform graphically the figure into one wherein the sides with unknown quantities are made…

A: Data given: Line Bearing Length AB S86°35’W 607.66m BC S31°35’W 301.08m…

Q: Example 3: The plan of plot was prepared by taking measurement with a 30 m chain. The area of plot…

A: ###Calculation of true area of plot in surveying###

Q: A circular region of radius R/2 is cut out from the circular region of radius R as shown. For what…

Q: .b\ In measuring a straight line, you come across: 1.a pond, 2. a tall building. Describe how you…

A: Obstruction while chaining and ranging

Q: 4. WHAT IS THE HEIGHT OF THE FLAGPOLE (H) IF THE Hi at point A is 1.45m and at point C is 1.66m, ß =…

Q: -60 20 10 40 100- 10 -30 -15- 60

A: THE BASIC COMMANDS USED ARE 1. LINE 2. CIRCLE 3. OFFSET 4. XLINE 5. DIMENSION 6. LAYER

Q: Compute the average-end area volume of the figure below. round answer to nearest whole cubic yard…

A: Given data:-

Q: The shaded area shown below is bounded by the line x4 m on the left, the-axis on top, and the curve…

Q: Determine the magnitudes of the forces T2, given that the resultant force of 210 N is acting…

A: Now FR¯=0i+0j-210k NT1¯=T11i-2j-6k6.4031T2¯=T22i+3j-6k7T3¯=T3-2i+3j-6k7

Q: 2.335 1.784 2.073 2.012 2.348 2.530 2.591 2.165 1.890 108.513

Q: B) Determine the order and degree of the following differential equation 1) y' + x?y = xe* 2) y" +…

Q: What reduction factor are we going to use if p > Pb a. 0.9 b. 0.65 C. 0.45 d. Ø= 0.65 +0.25 Ey - Et…

Q: Prepare and complete profile level notes, show the customary arithmetic check and plot the…

A: Prepare and complete profile level notes, show the customary arithmetic check and plot the profile

Q: 3. Complete the differential level notes shown below and perform the customary arithmetic check.…

Q: Compute the height of a building (in feet), given the following data: • Instrument Height = Rod…

A: Horizontal Distance to Prism, D = 142.68 feetThe Zenith Angle, The zenith angle is the angle…

Q: You use the following distances for a peg test: AM = MB = 50.000 !! PA = 5.000 If Enr is 0.026, E,…

Q: According to the figure below, fill out the table showing all your calculations: a) find the…

Q: A railroad curve has De = 5°00', I = 28°00', and PI station = 37+45.00 ft. Use the chord definition…

A: Dc = 5o00'I = 28o 00'PI station = 35+45.00 ftTo find:A. The radius of the curveB. The length of the…

Q: (1) What is the bending moment at B? (include the unit in the answer), (2) What is th bending moment…

A: To Find Bending moment at B & C Maximum shear Force & it's location. Maximum bending moment…

Q: A- In the rectangle below, a = 30.05m ±0.025, b=22.30m 10.015. Calculate the standard Error in the…

A: Given:- a=30.05 m ±0.025b=22.30 m±0.015 To find:- Standard error Concept:- Standard errors are a…

Q: 9.16 Figure (a) shows the cross-sectional dimensions of a structural steel section known as…

Q: A- In the rectangle below, a = 30.05m 10.025, b= 22.30m 10.015. Calculate the standard Error in the…

A: The below figure is shown,Where,To find:-Standard Error in the total area of…

Q: Determine the lengths of 2 sides (a and b) and area of an oblique triangle. You must provide…

Q: Determine the center of gravity for the triangle with cut of as shown in following figure: 12" 34

A: x¯= 12x12''x9''x12''3-5''x3''x(1''+2.5'')12x12''x9''-5''x3'' = 4.192''…

Q: Using parallelogram law, determine the magnitude of the vector F. 200 Ib A. 295.44 lbs B. 254.94 Ibs…

A: Given force 200lb Using parallelogram law To Determine The magnitude of the vector F.

Question

100%

Q1/ From the Figure below, calculate the height of the building if the distances AB=5m, DD1=1.2m and
BT=25m?
Rods
line of sight
25 m
E
1.5 m
Building
A 5m B
Q2/ Describe how would you find the suitable scale of the map to draw the plan of drawing having
dimensions (10 *20)m on the sheet drawing with dimensions (210 * 290) mm.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Given the following information on the sketch, compute the following: Coordinates at C, distance AC, bearing (RAD PT) to C. A N=846.05 E=486.18 $30 47'11'E C 100 Coordinates of C: N= Distance AC = PL 2 Bearing (RAD PT) to C=_ PL R=384.30 RAD. PT N=356.58 E=1097.54 E=
The areas of cut of two irregular sections 60m apart are 32m2 and 68m2 respectively. The base width is 8m with a sideslope of 1:1. Find volume using end area method select the correct answer: A. 3100 m3B. 3500 m3C. 3000m3D. 3200 m3
why divide x' in 2 in above method?
The areas in cut of two irregular sections 45 m apart are 44 m^2 and 66 m^2 respectively. The base width is 10 m and the side slopes are 1:1. Find the following: (a) Volume by end-area method (b) Volume by Prismoidal Formula Provide all necessary steps and diagrams if needed. Please write where I could clearly what letter or number is written. Thank you.
A line AB is 40 mm long.Endpoints A & B are 20 mm in-front of Vertical Plane.Endpoints A is 15 mm above Horizontal Plane at 45 degrees.Draw projections & trace of the line.
34-A Use the CAD drawing below and determine distances A and B to the nearest hundredth inch. 3.25 A = .88 .94 .92 .90 75- ➡.50" 2.45" A- 1.75" 12 .25" 156 DIA. (2 HOLES) 25" R Cengage Learning 2013
First write question on plan fair paper after then give solution on that paper I will like your solution
What is the area of the below triangle if you know x=213, y=267, and z=133? X K
Please Show the steps to get the answer.
First write question on plan fair paper after then give solution on that paper I will like your solution
Examp;e: The following Figure with two projections, assign the types of these projections and draw them with the third projection.
Q2) Draw contours of 13m, 19m and 30m by interpolation method, with suitable scale. RLs at corners are shown on figure below. Recorded data are in meter. 22 13 7 25 19 14 31 28 23 5.00- 27 32 27 5.00