Answered: 2m 3 8 4 5 (3) 6 (4 90° 2 2 m 5 4 00000…

2m 3 8 4 5 (3) 6 (4 90° 2 2 m 5 4 00000 (2) 3 1 24 1 2 kN PART B Determine the horizontal displacement of joint "2" and the force in all members. Take A = 300 mm² and E = 200 GPa.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: a-33.8 kN, b-27.2 kNc-4.8m "a" KN D "KN "KN H A-40 x 10 mm² 4 5m 4m A-60 x 10 mm A-40 x 10 mm² "C'm

Q: Express the internal shear in the beam shown as a function of x. Determine the shear force just to…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Truss A truss is a construction made solely of elements with two forces. A construction with…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: The rod ABC is made of an aluminum for which E = 70 GPa. %3D Knowing that P= 6 kN and Q = 42 kN,…

Q: Part 2 Refer to Problem 12.6, what would be the average degree of consolidation (U) of the clay…

A: To find Degree of consolidation of the clay layer (U)

Q: 6. A 100 N force acts along 10 points the line AB, as shown in the figure below. Determine the…

A: Consider the given figure Given data F=100 NL=20 mmB=20 mmL and B are length and breath of the…

Q: the bending moments m of the beam is given by dm/dx=-w(l-x) where w and l are constants,determine m…

Q: 8. Find force at any element. Calculate displacement for node 2 and 3. A=2cm2 ve E=200GPa 60 kN 3…

A: for finding displacements we are using UNIT LOAD METHOD

Q: e the method of virtual work and determine the vertical and horizontal displacement of joint F of…

A: A truss is normally the structure and the members are set up in a triangular method, objected to…

Q: Determine the vertical displacement of joint C of the steel truss shown inFig.a. The cross-sectional…

A: Given Data: The cross-sectional area of each member is A=400 mm2. The modulus of elasticity of the…

Q: Calculate for the axial force in kN at member CB of the frame shown in figure 2 using Cantilever…

A: Answer We have two assumptions of cantilever method to find axial force in member CB. 1) Point of…

Q: A #2 Determine the slope and the displacement at the end C of the beam. E = 200 GPa, I 70(106) mm².…

A: Slope and displacement at the end C

Q: q(x)= q0[1-c(x/L)] is the distributed load in the truss system given in the figure. It is a built-in…

Q: #1 Determine the vertical displacement of joint A. Each bar is made of steel and has a…

A: Given: P=54KN, a = 2m Required: Vertical displacement of A

Q: Calculate for the axial force in kN at member HG of the frame shown in figure 2 using cantilever…

Q: 1. Determine the vertical displacement of section B. The rigidity of AC is 2EI, the rigidity of BC…

A: For determining deflection at point B we will be using the conjugate beam method. In this method…

Q: Determine the height h above the base of the centroid of the cross-sectional area of the beam.…

Q: Determine the magnitude of the vertical displacement of joint C of the truss (in units of mm). Each…

Q: 2. The rigid bar BC that has a length of 10.5 ft is supported by steel rod AC of cross- sectional…

A: We will find vertical component of actual deformation.

Q: The lower ends of the three steel bars in Figure are at the same level before the applied…

Q: Determine the vertical displacement of joint C of the truss. Each member has a cross-sectional area…

Q: Determine the bar force of member BD (in kN) of the truss shown if P 18 kN and Q = 90 kN. Use 3…

Q: Determine the maximum bending moment magnitude for the beam shown below. Use a = 18 ft, b = 6 ft,…

A: Solution:- Bending moments at various sections: BMC=0BMB=-6×6×62 =-108 kip.ftBMA=-6×24×242+96×18 =0…

Q: Determine the vertical displacement of joint A (a) if members AB and BC experience a temperature…

Q: Bar ABC has a rectangular cross section of 300mm by 100mm. Attached rod DB has a diameter of 20mm.…

A: Understanding the AC CircuitThe question likely involves an AC circuit containing an inductor (L)…

Q: 5. Determine all force members. E 5m 5m ŠOKN GOKN 6. Solve for the force members BC, BE and BF. All…

A: If the force is Away from the joint : Tensile Towards the joint : compression We can solve…

Q: A symmetrical beam cross section is shown below. The centroid is in the exact centre of the section.…

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

A: Given,

Q: The double-collar bearing is subjected to an axial force P = 16 kN. Assuming that collar A supports…

A: It is required to determine the load supported by the collar A. It is required to determine the…

Q: Determine the force in each member of the loaded truss. Discuss the effects of varying the angle of…

A: Given figure is as ;To Find: Forces in each member.

Q: Virtual Work for Trusses #1 Determine the vertical displacement of joint A. Each bar is made of…

A: Given:- A truss is given with point load P The magnitude of the point load P = 91 The…

Q: A Aluminum L = 3 ft A = 0.75 in.² E = 10 x 106 psi 2ft 3 ft. с B Bronze L = 4 ft A = 0.25 in.² E =…

Q: Use the VIRTUAL WORK method. a.) determine the vertical displacement of joint A. Each bar is made…

A: Given: Required: Vertical displacement of joint A And why solving reactions of support is not…

Q: The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.27 in2. Find the…

Q: Q#5. Determine the displacement at point C and slope at point B of the steel beam shown. El is…

Q: Each bar is made of steel and has a cross-sectional area of 600 mm. Take E = 200 GPa. 5. Determine…

A: Note: Hi! Thank you for the question, As per the honour code, we are allowed to answer three…

Q: a 33.8 kN, b 27.2 kN, c-4.8m KN D "KN KN 4m 5m A-40 x 10 mm² A - 60 x 10 mm² C B H K J A-40 x 10³…

Q: Determine the horizontal displacement of joint B. You can assume that joint B displaces to the left.…

A: To find the horizontal displacement at the point B in the truss.

Q: Determine the forces in members BC, BE, and BF. The triangles are isosceles. The forces are positive…

Q: 8-11. Determine the horizontal displacement of joint A of the truss. Each member has a…

A: Given: Required : Horizontal displacement at A

Question

2 m
3
8
(4)
5
(3)
7
6
4
90°
2
2 m
5
ooooo
3
24
(1
2 kN
PART B
Determine the horizontal displacement of joint "2" and the force in all members. Take A =
300 mm² and E = 200 GPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 5 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Determine the force in each member of the structure and establish whether the members are in tension or compression. Establish P1= 45 KN, P2= 30 KN Solve the problem considering the following: The force P1 will be the maximum point of a triangularly distributed load with a horizontal distribution of X meters. You must leave the solution in terms of X and show the particular solution when X is equal to 0m and 2m.
Problem 2 For the beam shown in the figure A) Draw the shear-force and bending-moment diagrams for the beam shown in the figure. B) For the composite section, aluminium [E = 70 GPa] bonded to a steel [E = 210 GPa], located at the maximum bending moment, determine: (1) the maximum bending stresses in the aluminium and steel bars. (2) the stress in the two materials at the joint where they are bonded together. K4N/M 2m B 10kN/mm 4m 2m D Steel Aluminum 42mm 20 mm 13 mm
Calculate for the axial force in kN at member GC of the frame shown in figure 2 using cantilever method. Enter absolute value and use 2 decimal places in your solution. a = 33.8 kN b = 27.2 kN C= 4.8m
The steel bars AC and BC, each of cross-sectional area 120 mm2, are joined at C with a pin. Determine the displacement of point C caused by the 15-kN load. Use E = 200 GPa for steel.
The cross sectional area of the members of the truss shown is 500 mm² and E = 200 GPa. Solve the horizontal displacement of joint C due to external loadings in mm. AB 1.5 m O 0.1875 O 0.075 O 11.25 O 18.75 C 2 m D 10 kN 5 kN
Determine the reactions at the supports. The moment of inertia for each segment is shown in the figure. Assume the support at B is a roller. Take E = 29(103) ksi.
P 40 lb-in Fin 6 lb/in The frame shown in the figure is supported by a hinge at A and a frictionless wheel F. When P = 8 lb, determine (a) the reactive forces at support A and the bottom of the wheel, and (b) forces applied to member ABCD. ABCD is a single member. So is CEF. Points B, C, and E are pin joints.
Final answer. 0.288 in
r The two 4° wedges are used to position the te column under a load L. What is the least value of the e coefficient of friction u, for the bottom pair of sur- faces for which the column may be raised by apply- ing a single horizontal force P to the upper wedge? H1=0.30 IS. H2 0.378 %3D H2
6) Determine the vertical displacement of joint A. AE is constant. Take A= 2 in and E=29 (10') for each member. Use the principle of virtual work. D 8 ft B 8 ft 1000 lb 8 ft 500 lb
DETERMINE THE VERTICAL DISPLACEMENT OF JOINT A. EACH BAR IS MADE OF STEEL AND HAS A CROSS SECTIONAL AREA OF 600mm?. USE E=200GPA. -1.5 m 1.5 m 5 kN
Determine the horizontal displacement of joint A of the truss. Each member has a cross-sectional area of A=300mm2, E=200GPa. Use Catigliano's theorem.