Q3: At the parallel operation of three-phase transformers: a) Give an explanation for the following cases: i. Two-lamps are glow-up ii. Three-lamps are glow-up b) Two three-phase 11kV/ 380 V transformers are connected in parallel to serve a load of 36 kVA at unity power factor. The secondary side current for one transformer is 14.1 A, determine the load sharing for each transformer and the current of the other transformer.

Q3: At the parallel operation of three-phase transformers: a) Give an explanation for the following cases: i. Two-lamps are glow-up ii. Three-lamps are glow-up b) Two three-phase 11kV/ 380 V transformers are connected in parallel to serve a load of 36 kVA at unity power factor. The secondary side current for one transformer is 14.1 A, determine the load sharing for each transformer and the current of the other transformer.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

q3
In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220, then the percentage regulation is 4.54%. Select one: True False
No-load operation and short circuit tests were performed on three-phase, 50 Hz 480/220 delta / Y connected transformer. In these testsThe line voltage, line current and three-phase total power have been measured from the high voltage windings and the test results are below.pictures. 100 A DC current when 1.08 V DC voltage from non-transferable software is applied to the low voltage windingshas attracted.Find the single phase equivalent circuit parameters of this transformer.idle test:Voltage: 480V Power:114w current: 0.71Ashort circiut test:V: 10v P: 78w c: 18.3a
A Cock-croft Walton type voltage multiplier has 7 stages with capacitance all equal 0.07pF. The supply a frequency of to be supplied is 6.5mA. to transformer secondary voltage is 133kV at 250HZ. If the load current The total voltage ripple of the system is: (a) 15.3kv (b) 12.2kv (c) 9.1kV (d) 10.4kv (e) 1.9kv a. d O b. a OC C O d. e O e. b
Ql-phase step down transformer 1250 KVA, 10002200 V, 50 Hz The resistance /phase and leakage reactanceiphase of the primary winding are 0.78 2 and 4.82 and the corresponding values for the secondary winding are 0.012 and 0.002 respectively if the primary winding is connected in delta and secondary in star calculate: )The voltage to be applied at normal frequency to the primary to circulate full-load through it when the secondary is short-circuited li) The full load copper loss
2.Fringing effect is a phenomena occurs in .. (a)Transformers. (bElectrical field. (e)Air gap (d)All of the above. 3, The kVA rating of an ordinary 2-winding transformer is increased when connected as an autotransformer because (@ transformation ratio is increased (b) secondary voltage is increased (c) energy is transferred both inductively and conductivity (d) secondary current is increased. 4. The .... of the hysteresis loop is a measure of energy lost per cycle (a) area. (b) Туре. (c) Frequency (d) No one of the above. 5. At relatively light loads, transformer efficiency is low because (a) secondary output is low (b transformer losses are high (c) fixed loss is high in proportion to the output (d) Cu loss is small. 6. In an ideal transformer, (a) windings have no resistance (b) core has no losses (c) core has infinite permeability (d) all of the above. 7. In electromagnetic circuits, path of eddy current is.... (a) Parallel to the path of the flux. (b) Perpendicular to the path of…
2. Given three identical ideal single-phase transformers with each rated at 100KVA and 7kV/3.5kV, they are connected as a three-phase transformer bank. The three-phase transformer has high voltage side connected in delta and the low voltage side is connected in wye. A three-phase 200KVA, wye connected load is connected at the low voltage side of the transformer. Calculate the following: a. Rated line-to-line voltage on each side b. Line current on each side of the transformer
In a single phase transformer, when no-load voltage is 230V and full load terminal voltage is 220, then the percentage regulation is 4.54%. Select one: True False
a single-phase transformer serves a 7.2kw resistive loadlocated 200 ft from the transformer. each conductor from the transformer to load has an impedence of (0.78+j0.052) ohms per 1000ft. if the voltage at the load terminal is 240v, the magnitude of the voltage (v) at the transformer secondary is most nearly:
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.
A short transmission line connects a step-up transformer on the source side with a series impedance of j0.5 ohms (referred to the primary) to a step-down transformer on the load side with a series impedance of 50 ohms (referred to the primary). The turn ratio of the step-up transformer is 1:10 and a no-load primary voltage of 23 (line-to-line) kV. The step-down transformer has a turn ratio of 35:2 and it has a Y-connected, balanced load of 0.490 +j 0.0816 ohms connected to its secondary side. A capacitor bank of -j0.171 ohms is added parallel to the load. Assuming an ideal transmission line, the load voltage (line-to-neutral) would be: O A. 7360 V O B. 6.2 kV O C. 12750 V O D. 4806 V O E. None of the other choices are correct
Describe the star-delta connection configuration types in three phase transformers and their necessity by drawing and writing. Thank you very much if you answer.