It belongs to the no-load (no-load) operation of the 36/240 V phase transformer and a phase measured from the short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left empty and the unloaded test results were obtained. Rated currents to high voltage gates The decreasing energies were obtained in a short time from a short circuit by applying tests In direct current test The transformer with 1 V direct voltage applied to the low voltage winding draws 500 A direct current. All equivalent Calculate the circuit elements moved to the low voltage side. Boşta çalışma testi Güç Gerilim Akım 36 V 68 W 2,8 A Kısa devre testi Gerilim Güç Akım 15 V 325 W 42,2 A

It belongs to the no-load (no-load) operation of the 36/240 V phase transformer and a phase measured from the short-circuit test. values are given in the table below. High voltage by applying rated voltage to the low voltage winding (The winding ends were left empty and the unloaded test results were obtained. Rated currents to high voltage gates The decreasing energies were obtained in a short time from a short circuit by applying tests In direct current test The transformer with 1 V direct voltage applied to the low voltage winding draws 500 A direct current. All equivalent Calculate the circuit elements moved to the low voltage side. Boşta çalışma testi Güç Gerilim Akım 36 V 68 W 2,8 A Kısa devre testi Gerilim Güç Akım 15 V 325 W 42,2 A

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

SOLVE AND SHOW THE DIAGRAM: A 200-kVA, 3-phase, 50-Hz transformer has a voltage ratio (line voltages) of 33/11-kV and is delta/star connected. The resistances per phase are: high voltage 30 ohms , low voltage 0.88 ohms and the iron loss is 2000 W. Calculate the maximum efficiency and the efficiency at half load, both at 0.75 power factor lagging
A) In any transformer's core, we have two types of losses, what are they? B) Explain why the core has losses.
i need the answer quickly
The amount of inrush current in the primary of a transformer is limited by the........, A- amount of applied voltage, B- resistance of the wire in the primary winding, C- flux change of the magnetic field in the core, D - all of the above What precaution must be observed when working whit current transformers? A- never have a load on the secondary, B- always ha a load on the secondary, C- de-energize the primary whenever there is a load on the secondary, D - none The fact that the movable coil of a constant-current transformer moves further away from the stationary coil with a increase in load current is based on which fundamental priciple of magnetism? A- like magnetic poles attract, B- like magnetic poles repel, C- the amount of current flowing through a coil inverdely proportional to its flux density. D- none
Find the elements of the equivalent circuit relative to the secondary of a single-phase transformer. The no-load voltages in the primary and secondary circuits are 200,400 volts, respectively, at a frequency of 50 Hz The primary no-load current at voltage 200 equals 0.7 amps and pulp losses equal to 70 watts Primary resistance and reactance 3.2, 1.25 In order, the reactance of the resistance and the coil 0.6, 0.7 Then draw the equivalent circle, explaining the values
The resistances of potential transformer winding is minimized by using a thick conductors and small length of turns b thin conductors and small length of turns c thin conductors and large length of turns d thick conductors and large length of turns
The picture shown below is a. Step-Up Transformer b. None of the choices c. Step-Down Transformer
A normal transformer has a nominal 60 kVA. The nominal primary and secondary voltages are 600 V and 120 V respectively. If this transformer is connected as an autotransformer at 600 Vac a-) What would be the output voltages available using different connections? b-) Calculate the load kVA that the transformer can supply for each of the output voltages. c-) Calculate the currents of the windings for each one of the output voltages, indicating if it exceeds the nominal values.
4-If the transformer is loaded by purely capacitive load, what is the expected regulation and efficiency 5- If the transformer is loaded by purely capacitive load, what is the expected regulation and efficiency. 6-Writre the procedure of no load test of Single phase transformer and draw the connection diagram of this test
Transferred surge current method is used to find a. Fault in the transformer insulation b. Fault in the Circuit breaker c. Fault in the cables d. Fault in the lines
Blue is the numerical answer, I need a detailed solution.
Three-phase, 50 Hz 34500/10500 /Y connected transformer single-phase visible on the high voltage (primary) windings side Equivalent circuit parameters are given below. Each of the low voltage (secondary) windings of this transformer When a 7.5 ohm star connected resistive load is connected and the rated voltage is applied to the high voltage windings Find the transformer efficiency. Total iron losses of three phases will be taken as 85000 W.