Q2\| Answer with True or False of the following question: 1. The column capitals decrease the effective span of the slab. 2. The total thickness of flat slab, should be not less than 150mm 3. The drops are provided in flat slabs to resist bending moment. 4. Deflection in slabs can be controlled by using appropriate aspect ratio 5. Direct design method is more accurate than equivalent frame method.

Q2\| Answer with True or False of the following question: 1. The column capitals decrease the effective span of the slab. 2. The total thickness of flat slab, should be not less than 150mm 3. The drops are provided in flat slabs to resist bending moment. 4. Deflection in slabs can be controlled by using appropriate aspect ratio 5. Direct design method is more accurate than equivalent frame method.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Assume the section has cracked and use the transformed-area method to compute the required parameters for the beam shown. Solve for: 1.) The value of k from locating the neutral axis using Qtop=Qbot is 2.) The value of j 3.) The compressive stress on concrete in psi 4.) the tensile stress on the tension bars in psi
REINFORCED CONCERETERefer to the sample problem below (b = 400 mm, d= 550 mm, 4-25 mm diameter rebars). Determine if the beam is safe using the "transformed section method". sample problem: The cross-section shown below is a rectangular beam reinforced for tension only. Determine whether the section is safe or not to carry the loads shown. fs= 138 MPa. f'c = 20 MPa. n = 12. Neglect weight of beam.
Compute the flexural stress (MPa) in the steel for the beam shown using transformed-area method. Area of 1-#29 bar is 645mm?. Assume cracked section. 530 mm 600 mm M = 130 kN-m n = 9 4 #29 70 mm - 350 mm
A) Determine the shape factor and the Fully Plastic Moment (Mp) for the shaded symmetrical hollow rectangular beam section shown below. Assume the yield stress Oy =275 N/mm². B) If two plates of width 250 mm and thickness equal to 't' mm is connected (fabricated) at top and bottom (one plate on each side) for the given section, then what is the improvement in the fully plastic moment(Mp) of the section. C) If this revised fabricated section is now rotated by 90 degrees, what is its effect on the shape factor of the section? 200 mm. 50 m 100 ma 400 t- 10mm Note Take the value the 't' as equal to the last two digits of your studentid. If the last two digits are zero then take timm
Use the composite Simpson's 1/3 rule with step length h = 0.4 to estimate In(2 + 3/x) -dx, I = 1+x?
This is civil engineering. Everything needed is provided. Please answer all parts to the best of your ability. Provide thorough answer and explanation.
Please show all steps
SITUATION B: The beam is to carry an Ultimate Moment of 580 kN-m, geometrical property of the beam are the following: width of the beam = 350 mm, total height of %3D the beam = 670 mm , steel cover = 50mm. Use concrete strength f'c=21 MPa, steel %3D yield strength fy = 415 MPa and Ø = 0.877 %3D 4. What is the minimum number of 28-mm diameter reinforcing bars needed in the tension zone?
A concrete one-way slab has a total thickness of 120mm. The slab will be reinforced with 12 mm diameter bars with fy=275 MPa, fc'= 21 MPa. Determine the area of rebar in mm^2 if the total factored moment acting on 1m width of slab is 23 kN-m width of slab is 23 kN-m. Clear concrete cover is 20 mm.
Q2-c) Solve problem below using flexibility matrix method Settlements 8mm and 30mm at supports 2 and 3. (Use conjugate beam method) -7m 2 2 7m 3 El= constant E = 200 GPa I = 145(106) mm² 3 7m 4
Use USD method.