Q2(a) Figure Q2(a) shows the spacing of a double circuit 3-phase overhead line. The phase sequence is UVW and the line is completely transposed. i) Critically assess the advantages of double circuit line over single circuit line ii) Calculate the inductance per phase for 500 meter length of line using Table 2(a) data for the Figure Q2(a). Table 2(a) GMR of the line Distance a-b' Distance c-c' 0.01m 6.m 8.3m Figure Q2(a)

Q2(a) Figure Q2(a) shows the spacing of a double circuit 3-phase overhead line. The phase sequence is UVW and the line is completely transposed. i) Critically assess the advantages of double circuit line over single circuit line ii) Calculate the inductance per phase for 500 meter length of line using Table 2(a) data for the Figure Q2(a). Table 2(a) GMR of the line Distance a-b' Distance c-c' 0.01m 6.m 8.3m Figure Q2(a)

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Calculate the inductance per phase per meter for a three- phase double-circuit line whose phase conductors have a radius of 4.1 cm with the horizontal conductor arrangement as shown in Figure below A B A' C' B' 6m -6m 7 m 6m- 6m
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1cm diameter. The conductors are arranged in a horizontal configuration with 0.71 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux link- ages, and (c) the total inductance of the line.
In the following network, the voltage magnitudes at all buses are equal to 1 p.u., the voltage phase angles are very small, and the line resistances are negligible. All the line reactances are equal to j1 p.u. (1) (2. P₂ = 0.1 p.u. P3 = 0.2 p.u. The voltage phase angle 83 in radian at bus 3 is (Assume one of the generator bus as slack bus and sin-¹ (0.1) = 0.1 rad) (a) -0.1 (b) -0.2 (c) 0.1 (d) 0
The % voltage drop is calculated for 3-phase systems by taking phase quantities and per phase line parameters True False
In a 3-phase Overhead System, each line is suspended by a string of 3 Insulators. The voltage across the top unit and middle unit are 10KV and 11KV respectively. Calculate (i) Ratio of Shunt Capacitance to Self-Capacitance of each insulator and (ii) String Efficiency
Problem 1 a- Explain the meaning of the term "bundle conductor transmission line" and discuss the effects of its use on the electrical performance of a high voltage electric transmission line. b- Consider an experimental 1800 kV three phase bundle-conductor line with parameters A= 0.95 and B=j 70. Determine the value of the parameter C of the line. Assume that the line is delivering 2,000 MVA at receiving end whose voltage of 1750 kV and unity power factor. Determine the sending end voltage of the line. d- C- Determine the sending end current of the line.
Question 1) A 154 kV transmission line has a length of 100 km. The line and the conductors are given in Figure 1. The line is operated at f= 50 Hz. For both old and new lines calculate; a. GMD and GMR. b. Inductance of the line in Henries (H). c. Series Impedance (Z) of the line in Ohms. d. *Compare the results for both lines and comment on the results. e. *If the distance between the two neighbouring conductors is increase from 13 meters to 15 meters what would be the parameters in part a.,b. and c. comment on the results. New Line's Conductors 13 m 13 m Old Line's Conductors d r = 2 cm d = 40 cm r = 2 cm Figure 1
For the system shown in figure, voltages V2, V3 and angles 82, 83 are calculated using Newton-Raphson method. shunt line charging admittances are neglected. All the values are given in per unit on 100MVA base. Calculate the complex power flows S12 and S32 in actual units. 1) Z12 = 0.01+ j0.02 Z3 = 0.02+ j0.04 PL G QL Slack bus V2 = 0.96L -1.67° V3 = 0.884 - 5.48° Vi=1.0/0° (estimated time to answer this question: 13 minutes)
The single line diagram of a power system is shown in Figure Q2.1 including generator and transformer winding connection and earthing details. The parameters for this system have been calculated on a common 100 MVA base and are given in Table Q2.1. All resistances and shunt susceptances are neglected. This system experiences a single line to ground fault at a point F on line L1. The point F is at a distance d from Bus 4 along the line L1. The total length ?? of the line L1 is 50 km. Note that the location of ?? is not drawn to scale in Figure Q2.1. The fault current at the fault point F is measured to be 6.106 kA. i) Determine the zero, positive, and negative sequence Thevenin equivalent impedances as seen at the fault point F. These should be evaluated in per unit and shown as a function of d.ii) Use the sequence impedances calculated in part (i) to determine the distance d of the fault (in km) from Bus 4.