Q2/ Choose the correct answer. 1- The bit is connected to the lower end of the - A- drill pipes 2- B-drill collars C-drill string. is a casing string that does not extend back to the wellhead, but is hung from another casing string A- production casing B- intermediate casing C-liner. 3- traveling block and drilling line is called A- Drawwork B-block tackle C- rotary system 4- The drawwork is located at A- the derrick floor B-the mast C- the substructure 5- Objective of A- Relief well B- side tracking well. C- controlling vertical well. Solve all well is to intercept the borehole of a well for killing purpose

Q2/ Choose the correct answer. 1- The bit is connected to the lower end of the - A- drill pipes 2- B-drill collars C-drill string. is a casing string that does not extend back to the wellhead, but is hung from another casing string A- production casing B- intermediate casing C-liner. 3- traveling block and drilling line is called A- Drawwork B-block tackle C- rotary system 4- The drawwork is located at A- the derrick floor B-the mast C- the substructure 5- Objective of A- Relief well B- side tracking well. C- controlling vertical well. Solve all well is to intercept the borehole of a well for killing purpose

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The effective throat thickness of a fillet weld not to be greater than a. 0.3t b. 0.6t C. t d. 0.5t
Draw influece line for Rvd (Please focus on the solution process) P=1 Hinge P RvD اشا A - 4m a 13 C TMA4 72
m) what is the block shear rupture (L-shaped) capacity of flange plate of the flange connection in kips? (2 decimal places) A992: Fy=50ksi, Fu=65ksiA36: Fy=36ksi, Fu=58ksieffective bolt hole diameter = bolt hole + 1/16"beam properties: tw=0.38 in., bf=7.07 in., tf=0.63 in.Fexx=70ksi
based on my calculation draw a shear force and bending moment digram
weel loads are, 150 kn, 100 kn and 20 kn
Step 1 given; What the dismantling and Assemble of diaphragm valveAlso what is function of part than constant it Step 2 solution; Dismantling joint-It is very useful for joining and removing of pipe section with designing of dismantling joint. because its is used for joint longitudinal adjustment in pipe section for joining of pipe. without longitudinal adjustment ,It is not possible to insert valve for joining of longitudinal pipe. Diaphragm valve-diaphragm valve is flexible valve. which is used for controlling pressure when force is applied in valve then it will be automatically open or close on the basis of pressure adjustment. and it will control the flow rate of fluid. when less flow rate required then valve slightly closed on the basis of flow requirement. when more flow rate required then it will be open. function- it will change the speed and velocity of fluid.
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 2. The shear lag coefficient U and the effective area Ae
In the Cylindrical Cam system, the part attached to the Cam profile is called Select one: O a. Follower O b. Shaft O C Guide O d. Pin
7. /8 Using the figure below, answer the following: a. What type of weld is to be made? b. What is the significance of the square on the reference line? c. What is the depth of preparation on the arrow side? d. What is the effective size of the weld on the other side? True (³²³)
Given W 16x36 section as shown below (Fy = 50 ksi, Fu = 65ksi). The holes are 3/4 inch in diameter. The connection is bottled at the web only. Assume x= 0.76 inch. 1. The gross and net areas Ag and An.
Compute the capacity of the connection considering all modes of failure
5.15. For the connection shown in the accompanying fie. ure, what is the maximum required design strength OR? The load is 90% live load and 10% dead load. What weld size is indicated if E70 electrodes are used with the SMAW process? nw eous cent (b) Use AISC Manual Table 8-4, "Coefficients C for Eccentrically Loaded Weld Groups." 5" (130 mm) 6k (26 kN) 9 A (150 mm) A36 steel Problem 5.15