3 Pipes Connected in Series as shown in the Figure below:- 0 L₁ = soom d₁ = 0.06 m f = 0.02 2 Q=0.0117(m 011 7 (m²³/s) L₂=700m d₂= 0.08 m f = 0.02 L3= 600 m d₂=0-m f = 0.02 Required: Diameter of the equivalent pipe for these 3 pipes to carry the Same (@) and has the Same length (Summation of length of these 3 pipes).

3 Pipes Connected in Series as shown in the Figure below:- 0 L₁ = soom d₁ = 0.06 m f = 0.02 2 Q=0.0117(m 011 7 (m²³/s) L₂=700m d₂= 0.08 m f = 0.02 L3= 600 m d₂=0-m f = 0.02 Required: Diameter of the equivalent pipe for these 3 pipes to carry the Same (@) and has the Same length (Summation of length of these 3 pipes).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Question 3: The following system is used to drive water from the left tank to the right tank. The pipes are made of plastic. ( ›) a. Calculate the flow rate of water (. b. Calculate pressure loss through the tubes ( c. Calculate minor pressure losses ( H = 25 m Water D = 6 cm L = 5 m D = 4 cm L = 10 m 90° Threaded elbow D = 2 cm L = 5 m H = 5 m Water
Q1: Find the pressure in the pipe. Oil SG 0.79 P. gage 370 kPa Gasoline SG 0.70 Air 45 cm 50 cm Pipe 22 cm 10 cm Water Mercury SG= 13.6
H.W:- A line was measured with a (30 m) tape. This is standardized at (20 °C) under a pull of (10 kg). The measured length of line was (1500 m). The temperature during measurement was (30 °C) and the pull was (15 kg). Find: - 1- The corrected length of tape. 2- The true length of the line. Given the following: - 1- Coefficient of expansion (a) = 3.5x10-6 per °C. 2- Modulus of elasticity (E) = 2.1x106 kg/cm?. 3- Cross-sectional area of the tape (A) = 0.02 cm?.
Figure 3 Q1 Q2+Q3+Q4 = 1 Total losses = hL1+hL2+hL3+hL4+hL5 Q1 = Q5 The pipes in Figure 3 show a Simple Pipe Network. Which of the following statements are true for this set-up? Select all that apply. hL2hL3=hL4 hL1 = 2 hL2+ hL3+ hL4 3 4 5
Two 10”-15.3 lb channels are welded together as shown in the figure. Determine the moment of Inertia about the Xo axis.
Q1: What would be the maximum length of pipes 1 and 2 (L1 and L2) to allow passing 5 cfs in the system shown in figure below (Neglect minor losses and assume L1 L2). El. Z2 ft. |El. Z1 ft. L2 hp=M-Q? L1 f2 = 0.018 Z1=24 f = 0.015 D2 = 12 in D = 8 in Z2=145 M=165 QF17
ؤُال الثالث: )30 درجة( Q3: Draw the S.F and B. M. diagrams for the beam shown below. P = 625 lb L = 4 ft q = 80 lb/ft L2 = 8 ft - – → - L3 = 5 ft
Water in the reservoir is used to control the water pressure in the pipe at A. Take pHg = 13550 kg/m³ and p = 1000 kg/m³ Neglect the diameter of the pipe. (Eigure 1) Figure AQ B E h 400 mm C 150 mm 100 mm 200 mm Mercury pe he Y Part A If h= 140 mm, determine the gage pressure in the pipe at A when the mercury is at the elevation shown. Express your answer to three significant figures and include the appropriate units. PA 76.8 Submit 4 Provide Feedback kPa CINC Previous Answers Request Answer ? X Incorrect; Try Again; 4 attempts remaining
A pressure gauge tester is shown in Figure 3.3. The cylinder is filled with oil, B,=475×10-1²Pa-!. The diameter of piston is D=15 mm, the screw pitch t=2mm. At the atmospheric pressure, the volume of oil in the cylinder including pipeline is V=250cm³. For the reading of 25.0MPA in the pressure gauge, how many revolutions do the handwheel must screw in? 5 4 3 2 6 1. handwheel; 2. screw; 3. piston; 4. cylinder; 5. oil; 6. pipeline; 7. standard gauge; 8. gauge to be tested Figure 3.3 A pressure gauge tester
Consider the tank shown. Which of the following pressure relations is correct? Air Air 2 ft 3 ft Air 4 ft Water Select one: О а. Рс РD O d. Pp > PA
SHOW COMPLETE SOLUTION AND FINAL ANSWER INTO 3 DECIMAL PLACES 3. A large pipe called penstock in hydraulic work is 1.5 m in diameter. Here it is composedof wooden staves bound together by steel hoops each 300 mm2in cross sectional area, and is used to conduct water from a reservoir to a powerhouse. If the maximumtensilestress permitted in the hoops is 130 MPa, what is the maximum spacing between hoops under a head of water of 30m? Use density of water equal to 1000 kg/m3
Acompound shaft drives several pulleys, as shown in the figure. Segments (1) and (2) of the compound shaft are hollow aluminum [G=4,000 ksi] tubes that have a polar moment of inertia of 2.337 in.4. Segments (3) and (4) are solid steel [G=12,000 ksi] shafts that have a polar moment of inertia of 0.497 in.. The bearings shown allow the shaft to turn freely. Calculate the rotation angle (including the correct sign) of pulley Dwith respect to pulley & 175 lb-ft 20 in. 525 lb-ft D 40 in. 925 lb-ft 30 in. (1) 70 in.