Q2: A closed cycle gas turbine unit operating with maximum and minimum temperatures of 760°C and 20 °C has a pressure ratio of 7/1. Sketch the cycle on T-S and P-V diagrams and calculate the ideal thermal efficiency and the work ratio. Assume air as working fluid and consider as a perfect gas and take R-0.287 kJ/kg.k, c,-0.718 kJ/kg.K, c,-1.005 kJ/kg.K

Q2: A closed cycle gas turbine unit operating with maximum and minimum temperatures of 760°C and 20 °C has a pressure ratio of 7/1. Sketch the cycle on T-S and P-V diagrams and calculate the ideal thermal efficiency and the work ratio. Assume air as working fluid and consider as a perfect gas and take R-0.287 kJ/kg.k, c,-0.718 kJ/kg.K, c,-1.005 kJ/kg.K

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An Otto cycle with a compression ratio of 7.5 operates from the suction conditions 14.2 psia, 85 °F. Find the pressure and temperature at the end of compression, a) if cold air (k-1.4) is the working substance, b) if hot air (k-1,32) is the working substance.
): Consider a spark-ignition engine in which the effective volume ratio (V1/V2) is 8:1. Compare the P-V diagrams and the work done at the end of the compression process for an isentropic compression y-1.4 with that for a polytropic compression with a-1.3. The initial pressure in the cylinder is 100 kPa. Assume air as working fluid and consider as a perfect gas.
Thermodynamics Answer the following questions with complete solutions. write legibly An engine operates with air on the cycle shown with isentropic processes 1 - 2 and 3 - 4, and constant volume processes at 2 - 3 and 4 - 1. If the compression ratio (r) is 12, the minimum pressure is 200 kPa, and the maximum pressure is 10 MPa, determine the net cycle work (Wcycle) in terms of the final volume of isentropic compression process (V2). (Note: r = V1/V2 = V4/V3).
yale L 15 A gas power cycle uses air as the working fluid and has two turbine sections as shown in the figare below. The power produced by Turbine I is used to drive the compressor, and Turbine 2 produces output power W. Air enters the compressor with a semperature of 290 K and a mass flow rate of -2 (kgs] (State I); the air exits the compressor at 44SK (State 2). Heat is transferred from a high- temperature thermal reservoir, Ta- 1400 [K), to Heat Exchanger 1 at a rate Q,- The lemperature of the air is raised to 1100 [K] (State 3) as it flows through Heat Exchanger 1. The air enters Turbine I where it is expanded to State 4. The flow then proceeds to Turbine 2 and exits with a temperature of 500 (K] (State 5). Heat is then removed from the air through Heat Exchanger 2 at a rate Q which is rejectod to the low-temperature thermal reservoir, TL-200 (K). (A) Determine the temperature at the inlet to Turbine 2, Te (b) Calculate the power output from Turbine 2, W. (e) Calculate the rate of…
Q2. An idea Otto cycle has a compression ratio of 11, takes in air at 100 kPa and 25 °C. The rotational speed of the cycle is 2000 rpm. Using constant specific heats at room temperature, sketch P-V diagram of the cycle and determine the thermal efficiency and the rate of heat input if the cycle produces 180 kW of power
An idealcold air-standard Brayton cycle produces some quantity of power. Air with a mass flow rate of 6 kg/s enters the compressor at 100 kPa, 300 K.It is also known that the compressor has a pressure ratio of 10 and the turbine inlet temperature is 1400 K.If k = 1.4for the working fluid, determine the thermal efficiency, the ratio of back work, and the net power for the cycle in kW.
High-P turbine Low-P turbine Reheater Boiler P, = P3 = Preheat Pump Condenser
4:52 ¢ O !ןה. il 3.5 37 K/s Prmnnt 1 minute ago (CLO-6) A simple ideal Rankine cycle operates such that P- Pa 10 kPa and P2- P3-5 MPa. The turbine inlet temperature is 600°C. The schematic of the cycle is shown below. Water is the fluid in the cycle. Water is saturated liquid at the exit of the condenser and water is compressed liquid at the exit of the pump. Determine the heat rejected in the condenser. 9in Boiler Wpump.in Wrurb.out Pump Turbine Condenser Jout O O o ...
E Expert Q&A Show the heat pump that operates on the ideal vapor-compression refrigeration cycle, with refrigerant-134a as the working fluid, on T-s diagram as in Figure (1). T House Он 1.4 MPa Win 320 kPa 4 step: 2 of 8 For the given ideal vapor-compression refrigeration cycle, with refrigerant-134a as the working fluid,specific entropy, specific enthalpy, pressure, and specific volumeat state are $i, ", , and Virespectively. Also, the saturated liquid state is denoted by the subscript f, the saturated vapor is denoted by the subscript g, and the properties at latent stage are denoted by the subscript fg. th step: 3 of 8 (a) Use â€œsaturated refrigerant-134a 00 00 Tools 88 Home Courses 2.
(17 blanks) Calculate the efficiency of the Carnot Engine for ideal gas. Consider the figure below for a complete cycle of Carnot engine, where the cycle goes from ad->ab->bc->cd
turbine turbine Reheater (4 Boiler P4= P5 = Prcheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0 1 At state 1, the specific volume is 0.00101 m/kg Find the pressure in bar at state 6 to 3 decimal places
Q2: A closed Gas turbine unit operating within below temperatures and pressures. Determine the heat supplied; the power output; work ratio; and the cycle efficiency. Compressor ti-20 °C Pi 1 bar mar = 5 kg/s P:= 7 bar t-760 °C Combustion chamber Cooler Turbine HOA W₁=?