1. A closed-cycle gas turbine unit operating with maximum and minimum temperatures of 760 and 20 oC has a pressure ratio of 7/1. Calculate the ideal cycle efficiency and the work ratio. Take c, = 1.005 kJ/kgK and y 1.4.

1. A closed-cycle gas turbine unit operating with maximum and minimum temperatures of 760 and 20 oC has a pressure ratio of 7/1. Calculate the ideal cycle efficiency and the work ratio. Take c, = 1.005 kJ/kgK and y 1.4.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q3: What is the ideal Otto-cycle efficiency for a 8:1 compression ratio, and how does it compare to the Carnot efficiency for a flame temperature of 3000K?
View Image. Please Write Legibly. Box the final answer. Given: Solution:
A power plant operating in a Reheat Rankine Cycle produces steam at 3 MPa, 600oC in the boiler. It keeps the condenser at 45oC by transfer of 10 MW out as heat transfer. The first turbine section (high-pressure) expands to 500 kPa and then flow is reheated followed by the expansion in the low-pressure turbine. Provide a detailed solution. Avoid shortcuts. Solve for the High-Pressure and Low-Pressure Turbines work output (kJ/kg)
3 (a) A simple Rankine cycle uses water as the working fluid (Figure Q3). IA 9 in 4s 4 gout Figure Q3. Rankine Cycle The boiler operates at 7,000 kPa and the condenser at 100 kPa. At the entrance to the turbine, the temperature is 450 °C. The isentropic efficiency of the turbine is 90%, pressure and pump losses are negligible, and the water leaving the condenser is subcooled by 9.6 °C. The boiler is sized for a mass flow rate of 20 kg/s. Determine, (i) The rate at which heat is added in the boiler, (ii) The power required to operate the pumps, (iii) The net power produced by the cycle, (iv) The thermal efficiency. (b) After a long walk in the 14 °C outdoors, a person wearing glasses enters a room at 25°C and 60% relative humidity. (i) What is the difference between specific and relative humidity? (ii) Please explain whether the glasses will become fogged or not and why. An
provide a step by step solution for the following question in the added image
please provide full calculation
An idealcold air-standard Brayton cycle produces some quantity of power. Air with a mass flow rate of 6 kg/s enters the compressor at 100 kPa, 300 K.It is also known that the compressor has a pressure ratio of 10 and the turbine inlet temperature is 1400 K.If k = 1.4for the working fluid, determine the thermal efficiency, the ratio of back work, and the net power for the cycle in kW.
An ideal diesel cycle powered by air has a compression ratio of 20. At the beginning of the compression process, the pressure of the air is 100 kPa, the temperature is 20 °C and the highest temperature of the cycle must not exceed 2250 K. Show the cycle in the P-v diagram.Then calculate: a) The heat entering and leaving the cycle, the thermal efficiency of the cycle, b) the average effective pressure of the cycle. Assume that specific heat is constant at room temperature constant at temperature. k=1.4 CP=1.005 kJ/kgK CV=0.718 kJ/kgK R=0.287 kJ/kgK
turbine turbine Reheater (4 Boiler P4= P5 = Prcheat Pump Condenser The following data was given for a steam power plant operating on the ideal reheat Rankine cycle. 3-4: Inlet steam at 17.5 MPa and 600 °C 6-1: inlet steam at a pressure of 11.16 kPa at a wetness fraction of 0 1 At state 1, the specific volume is 0.00101 m/kg Find the pressure in bar at state 6 to 3 decimal places
A simple Rankine cycles operate with an initial pressure of 1.69546 Mpa and 370.546oC temperature and exhaust to a heating system at 0.189546Mpa. Compute the turbine work, heat of steam generator, heat rejected, thermal cycle efficiency, and thermal engine efficiency. Draw schematic diagram and T-s diagram.
Determine percent change in efficiency of Otto cycle when Compression ratio is changed to 12 from 8.
On the diagram below sketch a basic Rankine cycle with superheating. Assume that there are irrevesibilities in the turbine and pump. Identify the device associate with each process. Make sure to label: the states and include important features, e.g. lines of constant temperature, volume, pressure, entropy, vapor dome, etc.