Q2: A closed Gas turbine unit operating within below temperatures and pressures. Determine the heat supplied; the power output; work ratio; and the cycle efficiency. Compressor ti-20 °C P₁= 1 bar mar = 5 kg/s P:= 7 bar t-760 °C Combustion chamber Cooler Turbine HOA W₁ =?

Q2: A closed Gas turbine unit operating within below temperatures and pressures. Determine the heat supplied; the power output; work ratio; and the cycle efficiency. Compressor ti-20 °C P₁= 1 bar mar = 5 kg/s P:= 7 bar t-760 °C Combustion chamber Cooler Turbine HOA W₁ =?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Stirling Cycle Answer with complete solution and explanation, and with cancellation of units.
Q1. Sketch T-s diagram for Rankine cycle with clear label for the following condition: Condensate pressure = 100 kPa • Boiler pressure = 3 MPa • Inlet temperature to the turbine = 350°C Determine thermal efficiency of the cycle. ANSWER
A cycle operates on air occurs as follows: an isentropic compression 1-2, a constant-pressure expansion 2-3, an isentropic expansion 3-4, and finally a constant volume cooling 4-1. The ratio of compression is 14, the ratio of expansion during constant-pressure expansion is 2, P1=47kPa, T1=32o C, V1=0.2m3. a. Find the heat added b. Find the heat rejected c. Find the work on each process and the net work
can you draw and schematic and t-s fiagram for this actual reheat rankine cycle State 1: Status: Saturated Liquid 30 kPa From Table A5 when ʋ1=ʋf = 0.001022 m3/kg h1=hf = 289.27 kJ/kg State 2a: Status: Compressed liquid P2s=PH= 6000 kPa h2a= 296.04 kJ/kg [ WP, ise= Wpact = State 3 Status: Superheated Steam P3=PH=6000kpa T3=Tmax= 550°C From Table 6A, When = 6000 kPa and =550 =3423.1 kJ/Kg =6.8826 kJ/Kg⸼K
Rankin cycle (Thermodynamics) Show complete and step by step solution. And show the diagram.
b- An evacuated tank ,shown if fig of 1 ft3 is coupled to air supply line through valve .When the valve is opened, the air flow from supply line at 70°F,120 psi until the pressure reaches 90psi . calculate the final temperature and mass inside tank ,assuming the process is adiabatic. R= 53.34 Ibf-ft/lbm °R use the table below in case. Alr supply line Tank Idcat-Gas Propertiles of Air (English Units)0, Standard Entropy at 1 atm = 161.325 kPa = 14.696 1bf/in.² (R) (Btulbm) (Btu/lbm) (Btu/lbm R) (R) (Btu/lbm) (Btu/lbm) (Btu/Ibm R) 400 68.212 95.634 1.56788 1950 357.243 490.928 1.96404 440 75.047 105.212 1.59071 2000 367.642 504.755 1.97104 480 81.887 114.794 1.61155 2050 378.096 S18.636 1.97790 520 88.733 124.383 1.63074 2100 388.602 532.570 1.98461 536.67 91.589 128.381 1.63831 2150 399.158 546.554 1.99119 540 92.160 129.180 1.63979 2200 409.764 560.588 1.99765 560 95.589 133.980 1.61852 2300 431.114 588.793 2.01018 600 102.457 143.590 1.66510 2400 452.640 617.175 2.02226 1000 172.564…
PART II: Gas turbine Introduction o Compressor (process 1 - 2) Work input, WC Increase pressure, pressure ratio p Wc = Win = mcp(T₂ - T₁) o Combustion of fuel (process 2 - 3) Heat addition, Qcc Increase temperature Qcc = Qin = m cp (T3 - T₂) o Expansion (process 3-4) High-energy fluid Useful Energy, WT WT = Wout = m Cp (T3 - T4) (1) Fuel Compressor Fresh air (2) Combustion chamber 3 Turbine Exhaust gases 4 w. net
Q3: An ideal air-standard Diesel cycle engine has a compression ratio of 18 and a cut- off ratio of 2. At the beginning of the compression process, the working fluid is at 100 kPa, 27°C. Determine the temperature and pressure of the air at the end of each process, the net work output per cycle [kJ/kg], and the thermal efficiency.
Here is the question Air enters the compressor ofthe cycle at 1 bar and 25 °C. Pressure after compression is 3 bar.Temperature at turbine inlet is 650 °C please specify these two parts answer too - a) heat rejected in the cooler ( is it Wc ?? ) b ) temprature of air leaving the solution ( is it T4 ?? ) I have already the solution please just highlight these two Answers
Thermodynamics The actual cycle of a 5T diesel engine, with a displacement of 7000 cm³ , 2,400 rpm is approximate to the theoretical cycle represented in the figure below, in which the custom rectangle has the area of the same cycle. A compression ratio is 17 and the thermal efficiency is 0.597 when 26.3% of the heat is provided isochorically. It is adopted that the active liquid has ϒ = 1.35 and R = 240J / KgK. To determine a) The values of p T and v at the main points of the cycle; b) The power of the cycle. c) Expansion work.
Thermodynamics subject power cycles. Show the ts diagram and complete and step by step solution. Box the final answer.
THERMODYNAMICS