Q18.A 415V, 3-phase,4 wire,suppliesin Figurestar-connectedsystemthreeresistive loadsasshownDetermine (a) the current in each line and(b) the current in the neutral conductor.OA24 kW415 V415 VINON12 kW18 kWly415 VOB

Answered: Image /qna-images/answer/63eb9b97-048a-4842-8c5f-04aaacf5c030.jpg

Q18. 415V, 3-phase, 4 wire, system supplies shown star-connected three loads Figure Determine (a) the current in each line and resistive as in (b) the current in the neutral conductor. IR 24 kW 415 V 415 V IN ON 12 kW 18 kW ly 415 V OB le

Q18. 415V, 3-phase, 4 wire, system supplies shown star-connected three loads Figure Determine (a) the current in each line and resistive as in (b) the current in the neutral conductor. IR 24 kW 415 V 415 V IN ON 12 kW 18 kW ly 415 V OB le

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.33MCQ: The direct electrical connection of the windings allows transient over voltages to pass through the...

See similar textbooks

Related questions

Q: Draw the network: 1 .Grounded Delta

A: A system in which the secondary side of the transformer is delta-connected and one corner of the…

Q: The single-line diagram of a subtransmision system is presented in the figure below. At point B a…

A: Three phase fault is the symmetrical fault and it is the most severe fault.

Q: In a single-phase alternator, a given field current produces an armature current of 250 A on…

Q: The one-line diagram of an unloaded power system is shown below. T | 1000 T Reactances of the two…

Q: Obtain the per-unit equivalent circuit for the following one-line diagram in Figure 1. Xine = 100 Q…

Q: Figure 1 shows a three-phase power system network comprises of synchronous generator, transformers,…

Q: In the figure, the load absorbs 22.256 KVA at a power factor 0.544639 inductive. For the feeder…

A: The solution is given below

Q: What size 60 degree Celsius conductors are required for a 9000 watt single-phase 120/240 volt…

A: The temperature for the conductors is T=60°C. The rated output power of the single-phase generator…

Q: On a base of 25 MVA , 11 kV the generator has reactances X,=X;=X;=0.2 pu and X = 0.06 pu . It is Y…

Q: 17 A3-phase generator rated 3000 KVA, 20 kV, 900 r/min, 60 Hz delivers power to a 2400 KVA, 16 kV…

A: In this question, We need to determine the value of voltage per phase if load of the system is…

Q: The AC motor M of figure shown in the next slide has 2300 Volts, balanced three phase voltage…

A: Motor terminal voltage =2300 V Power =120 KVA at 0.6 leading power factor We assume source and motor…

Q: 1.3 A 240 volts 50 Hz single phase ac source supplies a series load consisting of a resistor (40…

A: Given:A series R-L-C load is connected to 240 V 50 Hz single phase ac source. where, To find:i)…

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

100%

Q18.
A 415V, 3-phase,
4 wire,
supplies
in Figure
star-connected
system
three
resistive loads
as
shown
Determine (a) the current in each line and
(b) the current in the neutral conductor.
OA
24 kW
415 V
415 V
IN
ON
12 kW
18 kW
ly
415 V
OB

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.
A 500 kVA, 1100 V, 50 hz, wye-connected 3-phasehas armature resistance of 0.1 02/phase and synchronous reactance/phase of 1.502. (i) What is voltage regulation if the load pf is 0.9 lagging ? (ii) what is voltage regulation if the load pf is 0.8 leading?
Please solve d, e, f ONLY.
Q2\ Two generators G1 & G2 are rated 15 MVA, 11 kV and 10 MVA, 11 kV respectively. The generators are connected to a transformer as shown in the following figure. Find the sub- transient current in each generator when a three-phase fault occurs on the high voltage side of the transformer. A/Y 15 MVA, 11 kV, X"gl=j0.10 pu G2 15 MVA, 11/66 kV, Xr-j0.06 pu 10 MVA, 11 kV, X"g2-j0.10 pu
1. A single-phase power system as shown in Figure 1 consists of a 240 V, 60 Hz generator supplying a load, Zod = 8 + j6 Q through a transmission line of impedance, Zne = 0.08 + j0.14 Q. Answer the following questions: (1) transformer, T; and T2. Determine the voltage at the load and transmission line losses without the (ii) Determine the voltage at the load and transmission line losses with the transformer, T, and T2. T1 T2 1:10 10:1 IG Zaine Zioad source Figure 1
2A. What is another term for "shunt"? a) in series b) in parallel c) compounded d) none of the above 2B. Which of the following is/are a basic type of DC generator connection? a) series b) shunt c) compound d) all of the above
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
Equipment ratings and per-unit reactances for the system shown in the below figure are given as follows: Synchronous generators: GI 100 MVA 25 kV X1 = X2 = 0.2 Xo = 0.05 G2 100 MVA 13.8 kV X = X2 = 0.2 Xo =0.05 Transformers: TI 100 MVA 25/230 kV X = X2 = X, = 0.05 T2 100 MVA 13.8/230 kV X = X2 = Xo = 0.05 Transmission lines: TL12 100 MVA 230 kV X = X2 = 0.1 Xo =0.3 TL13 100 MVA 230 kV X = X2 = 0.1 Xo = 0.3 %3D TL23 100 MVA 230 kV X = X2 = 0.1 Xo = 0.3 %3D Using a 100-MVA, 230-kV base for the transmission lines, draw the per-unit sequene networks and reduce them to their Thévenin equivalents, “looking in" at bus 3. Neglect A-Y phase shifts. Compute the fault currents for a bolted three-phase fault at bus 3. 2 T2 b T1 TL12 to G1 G2 TL13 TL23 j0,03 j0,03 3
Please, I do not want a theoretical solution or using artificial intelligence. I want a solution on paper using the mathematical laws of the topic
Find the following : 1.Ripple Voltage (vpp) 2. Zero-to peak ripple(Vop) 3.secondary winding of the transformer high line and low line
The one-line diagram of an unloaded power system is shown below. T2 j 80 0 j 100 2 E Y uw Ts Reactances of the two sections of transmission line are shown in the diagram. The generators and transformers are rated as follows: Generator 1: 20 MVA, 13.8 kV, X" = 0.2 per unit Generator 2: 30 MVA, 18 kV, X = 0.2 per unit Generator 3: 30 MVA, 20 kV, X" = 0.2 per unit Transformer T1: 25 MVA, 220Y/13.8A kV, X = 10% Transformer T2: Single-phase units each rated 10 MVA, 127/18 kV, X = 10% Transformer T3: 35 MVA, 220Y/22Y kV, X = 10% Compute for the reactances per unit and by choosing a base of 50 MVA, 13.8kV in the circuit of generator 1. Show your complete solutions (41-48): 41. What is the generator 1 per unit reactance? a. 0.3333 b. 0.2755 c. 0.5 d. 0.2 42. What is the transformer 1 per unit reactance? a. 0.2 b. 0.1667 c. 0.1429 d. 0.0826 43. What is the transmission line 1 (point B to C) per unit reactance? a. 0.1033 b. 0.0826 c. 0.5 d. 0.2 44. What is the transformer 3 per unit reactance?…
A 10,000 KVA, 13.8 KV turbo-generator having x-x,-15% and x-5% is about to be connected to a power system. The generator has a current limiting reactor of 0.7 ohm in the neutral. Before the generator is connected to its system, its voltage is adjusted to 13.2 KV when a double line to ground fault develops at terminals band c. Find the initial symmetrical current in the ground and in the line. Ans: I, 2800 A; I=3090 A