Figure 1 shows a three-phase power system network comprises of synchronous generator, transformers, transmission lines and loads while Table 1 shows the ratings of the components. Using per unit analysis, 100 MVA base and 20 kV as the voltage base at the generator, answer the following questions: T2 TLine Load C Load A Load B Figure 1: A simple power system network. Table 1: The power system component ratings G 90 MVA, 20 kV, XG = 120% T1 80 MVA, 20/132 kV, XTI = 16% T2 80 MVA, 132/11 kV, XT2 = 10% TLine 132 kV, XLine = 18 2 Load A 7 MW +j3 Mvar Load B 30 MW+j 15 Mvar Load C 22 MVA, 0.89 power factor leading (a) Calculate the impedance per-unit values of all independent components based on given conditions.

Figure 1 shows a three-phase power system network comprises of synchronous generator, transformers, transmission lines and loads while Table 1 shows the ratings of the components. Using per unit analysis, 100 MVA base and 20 kV as the voltage base at the generator, answer the following questions: T2 TLine Load C Load A Load B Figure 1: A simple power system network. Table 1: The power system component ratings G 90 MVA, 20 kV, XG = 120% T1 80 MVA, 20/132 kV, XTI = 16% T2 80 MVA, 132/11 kV, XT2 = 10% TLine 132 kV, XLine = 18 2 Load A 7 MW +j3 Mvar Load B 30 MW+j 15 Mvar Load C 22 MVA, 0.89 power factor leading (a) Calculate the impedance per-unit values of all independent components based on given conditions.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

The shown distribution network is to supply two factories A & B with load curves indicated. Assume that both factories have a lagging power factor of 0.8 . a) Select the required sizes of transformers for both factories such that in the case of a failure in one transformer the overload on the remaining ones should not exceed 15% . b) Select the required sizes of fuses to be installed at both sides of transformers. c) Calculate the annual energy losses in transformers of factory A. Assuming that transformers are in operation continuously . d) Select the required size of the 11KV. XLPE cables for the distribution network , if cables are to be laid direct in ground with тахітит ground temperature of 30° С. e) Calculate the annual energy losses in cables of section SA . S 2 Km A 3 Km 11/0.4 KV Trans. 11/0.4 KV Trans. Factory A PF = 0.8 lag. Factory B PF = 0.8 lag. | S (KVA) 500 |S (KVA) 500 400 400 300 300 200 200 100 100 Time (hr) 24 Time (hr) 24 6. 12 18 12 18 Load curve of Factory (A)…
2.5.3 A three phase power system has two generator connected in parallel to a transformer and subsequently to a 230 kV transmission line. The ratings for the components are given as below: Generator 1:10 MVA, reactance of 12%. Generator 2: 5 MVA, reactance of 8%. Transformer: 15 MVA, reactance of 6% Transmission line: impedance of 4+j60 2, for which the reactances in percentage are based on the ratings of the respective components. Obtain the reactance and impedance values of the components in the system in percentage, based on 15 MVA and rated voltage of the components.
1. What is the purpose of conducting Open Circuit (OC) test?2. What is the purpose of conducting Short Circuit (SC) test?3. What are the classifications of Core Loss and Copper Loss?
A 4-bus three-phase power system consists of the following equipment: • Generator 1 connected to bus 1 with a rated power of 20MVA, rated voltage of 20 kV, and a series reactance of 0.4 p.u. • Generator 2 connected to bus 5, with a rated power of 12MVA, rated voltage of 10 kV, and a series reactance of 0.3 p.u. Transformer 1 connected between buses 1 and 2, is wye-wye connected with a rated power of 20 MVA, rated voltages 20/100 kV, and a series reactance of 0.1 p.u. • Transformer 2 connected between buses 4 and 5, is wye-wye connected with a rated power of 12 MVA, rated voltages 12/110 kV, and a series reactance of 0.15 p.u. • Transmission Line 2-3 connects buses 2 and 3 and had a series impedance of 50 + j75 ohms. • Transmission Line 3-4 connects buses 3 and 4 and had a series impedance of 40 + j80 ohms. • Load A connected to bus 3 and abosorbes20 MW and 10 MVAR. The voltage at bus 3 is 105 kV. 1) Draw the one-line diagram for the system. 2) Draw the per-unit, per phase…
6. In figure below the rating of reactance and various components are shown. A load of 50MW at p.f. lagging is taking from the 33kv substation which is to be maintained at 30kv. Calculate the terminal voltage of the synchronous machine (Vs) in pu, also represent the line and transformer in series reactance. The system is three phase system V6 11 kV 132 kV 132 kV 33 kV 50 MW Line 0.8 p.f. lagging j1000 50 MVA X 10% 50 MVA X 12% 30 kV
There is a three-phase system such that the phase current in the generator, lines and charging phase is the same. The phase voltage in the generator must be 1000 [V] with clockwise sequence. The connected load must be such that the phase current in each load is 10 [A] and its power factor is 0.97 “lagging”. a) Determine phase currents in the generator, lines and phase in the load
2.2. The figure below shows a radial transmission system with a generator having a per-unit voltage of 1.3 at an angle of 9 degree p.u. The load demand is 47MW at a power factor of 0.96lagging. Use the nameplate values of Transformer 2 as base values and calculate the following: Correct answers to three decimal places : 25..Per unit impedance of transformer and it's angle 26.Per unit voltage of the line and its angle 27.Per unit impedance of the line and its angle. And Reactance of the transmission line when the load consumes full-load (Ω).
The figure below shows the one-line diagram of a four- bus power system. The voltages, the scheduled real power and reactive powers, and the reactances of transmission lines are marked at this one line diagram (The voltages and reactances are in PU referred to 100 MW base. The active power P2 in MW is the last three digits (from right) of your registration number (i.e for the student that has a registration number 202112396, P2 =396). [10] Starting from an estimated voltage at bus 2, bus 3, and bus 4 equals V2 (0) = 1.15<0°, V3 = 1.15 < 0°, V4 1.1< 0°. 1- Specify the type of each bus and known & unknown quantities at each bus. 2- Find the elements of the second row of the admittance matrix (i.e. [Y21 Y22 Y23 Y24]). 3- Using Gauss-Siedal fınd the voltage at bus 2 after the first iteration. 4- Using Newton-Raphson, calculate: |- The value of real power (P2), at bus 2 after the first iteration. Il- The second element in the first row of the Jacobian matrix after the first iteration. 2 P2…
It is bartleybe's policy that if questions objective than you need to solve at least first 3 questions.
What is the alternators terminal phase voltage at shorted load condition? Explainand justify your answer in one(1) sentence.Use IA as the reference phasor.
Note: please solve the correct solution
L-type equivalent circuit and parameters for a continuous sinusoidal phase of a 5.5 kW, 1460 rpm, line voltage 220 V and frequency 50 Hz star-connected 3-phase ASM, ignoring core (iron) losses given as follows: R1=0.21 Ohm, R2=0.18 Ohm, X1=X2=0.66 Ohm and Xm=9.9 Ohm How many times the inrush current will be the rated current when the ASM is started directly? Answer options group 3.7473 5.2280 8.0815 7.1534 1.2558 4.3763 2.6455 6.3414