Q12- A three phase transformer 3300/400 V,has D/Y connected and working on 50Hz. The linecurrent on the primary side is 12A and secondary has a balanced load at 0.8 lagging p.f. Determinethe i) Secondary phase voltage ii) Line current iii) Output power Ans. (230.95 V, 99.11 A, 54.94 kW)

Step 1: Given: Transformer rating:Transformer connection:Frequency:Primary line current:Secondary…

Answered: Q12- A three phase transformer 3300/400…

C++ for Engineers and Scientists

4th Edition

ISBN:9781133187844

Author:Bronson, Gary J.

Publisher:Bronson, Gary J.

Chapter1: Fundamentals Of C++ Programming

Section: Chapter Questions

Problem 4PP

See similar textbooks

Similar questions

(Civil eng.) The maximum load that can be placed at the end of a symmetrical wooden beam, such as the rectangular beam shown in Figure 2.20, can be calculated as the following: L=S1dc L is the maximum weight in lbs of the load placed on the beam. S is the stress in lbs/in2. I is the beam’s rectangular moment of inertia in units of in4. d is the distance in inches that the load is placed from the fixed end of the beam (the “moment arm”). c is one-half the height in inches of the symmetrical beam. For a 2” × 4” wooden beam, the rectangular moment of inertia is given by this formula: I=baseheight3=12=24312=10.674 c=(4in)=2in a. Using this information, design, write, compile, and run a C++ program that computes the maximum load in lbs that can be placed at the end of an 8-foot 24 wooden beam so that the stress on the fixed end is 3000lb/in2. b. Use the program developed in Exercise 9a to determine the maximum load in lbs that can be placed at the end of a 3” × 6” wooden beam so that the stress on the fixed end is 3000lb/in2.
(Civil eng.) Modify the program written for Exercise 9 to determine the maximum load that can be placed at the end of an 8-foot I-beam, shown in Figure 2.21, so that the stress on the fixed end is 20,000lbs/in2. Use the fact that this beam’s rectangular moment of inertia is 21.4 in4 and the value of c is 3 in.
_____ predicts that transistor density will double every two years or less.
(Oceanography) The pressure, P, exerted on an underwater object can be determined by this formula: P=gh is the density of water, which is 1.94slug/ft3 . g is the acceleration caused by Earth’s gravity, which is 32.2ft/sec2. h is the object’s depth in the water in feet. a. Determine the units of P by calculating the units resulting from the right side of the formula. Check that your answer corresponds to the units for pressure listed in Table 1.1. b. Determine the pressure on a submarine operating at a depth of 2500 feet.
(Automotive) a. An automobile engine’s performance can be determined by monitoring its rotations per minute (rpm). Determine the conversion factors that can be used to convert rpm to frequency in hertz (Hz), given that 1rotation=1cycle,1minute=60seconds,and1Hz=1cycle/sec. b. Using the conversion factors you determined in Exercise 7a, convert 2000 rpm into hertz.
(Electrical eng.) a. Write, compile, and run a C++ program that calculates and displays the value of the current flowing through an RC circuit (see Figure 3.19). The circuit consists of a battery connected in a series to a switch, a resistor, and a capacitor. When the switch is closed, the current, i, flowing through the circuit is given by this formula: i=(EIR)et/RC Eisthevoltageofthebatteryinvolts.Risthevalueoftheresistorinohms.Cisthevalueofthecapacitorinfarads.tisthetimeinsecondsaftertheswitchisclosed.eisEulersnumber,whichis2.71828( roundedtofivedecimalplaces). Using this formula, write, compile, and run a C++ program to determine the voltage across the capacitor shown in Figure 3.19 when t is 0.31 seconds. (Note: The value of RC is referred to as the system’s time constant.) The program should prompt the user to enter appropriate values and use input statements to accept the data. In constructing the prompts, use statements such as “Enter the voltage of the battery.” Verify your program’s operation by calculating by hand the current for the following test data: Testdataset1:Voltage=20volts,R=10ohms,RC=0.044,t=0.023secondsTestdataset2:Voltage=35volts,R=10ohms,RC=0.16,t=0.067seconds b. Check the value computed by your program by hand. After verifying that your program is working correctly, use it to complete the following chart:
(Thermodynamics) The work, W, performed by a single piston in an engine can be determined by this formula: W=Fd F is the force provided by the piston in Newtons. d is the distance the piston moves in meters. a. Determine the units of W by calculating the units resulting from the right side of the formula. Check that your answer corresponds to the units for work listed in Table 1.1. b. Determine the work performed by a piston that provides a force of 1000 N over a distance of 15 centimeters.
(Heat transfer) The formula developed in Exercise 5 can be used to determine the cooling time, t, caused only by radiation, of each planet in the solar system. For convenience, this formula is repeated here (see Exercise 5 for a definition of each symbol): t=Nk2eAT3fin A=surfaceareaofasphere=4r2 N=numberofatoms=volumeofthespherevolumeofanatom Volume of a sphere sphere=43radius3 The volume of a single atom is approximately 11029m3 . Using this information and the current temperatures and radii listed in the following chart, determine the time it took each planet to cool to its current temperature, caused only by radiation.
(Mechanics) The deflection at any point along the centerline of a cantilevered beam, such as the one used for a balcony (see Figure 5.15), when a load is distributed evenly along the beam is given by this formula: d=wx224EI(x2+6l24lx) d is the deflection at location x (ft). xisthedistancefromthesecuredend( ft).wistheweightplacedattheendofthebeam( lbs/ft).listhebeamlength( ft). Eisthemodulesofelasticity( lbs/f t 2 ).Iisthesecondmomentofinertia( f t 4 ). For the beam shown in Figure 5.15, the second moment of inertia is determined as follows: l=bh312 b is the beam’s base. h is the beam’s height. Using these formulas, write, compile, and run a C++ program that determines and displays a table of the deflection for a cantilevered pine beam at half-foot increments along its length, using the following data: w=200lbs/ftl=3ftE=187.2106lb/ft2b=.2fth=.3ft

Recommended textbooks for you

C++ for Engineers and Scientists

Computer Science

ISBN:

9781133187844

Author:

Bronson, Gary J.

Publisher:

Course Technology Ptr

Operations Research : Applications and Algorithms

Computer Science

ISBN:

9780534380588

Author:

Wayne L. Winston

Publisher:

Brooks Cole

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

C++ for Engineers and Scientists

Computer Science

ISBN:

9781133187844

Author:

Bronson, Gary J.

Publisher:

Course Technology Ptr

Operations Research : Applications and Algorithms

Computer Science

ISBN:

9780534380588

Author:

Wayne L. Winston

Publisher:

Brooks Cole

Systems Architecture

Computer Science

ISBN:

9781305080195

Author:

Stephen D. Burd

Publisher:

Cengage Learning

Fundamentals of Information Systems

Computer Science

ISBN:

9781337097536

Author:

Ralph Stair, George Reynolds

Publisher:

Cengage Learning

C++ Programming: From Problem Analysis to Program…

Computer Science

ISBN:

9781337102087

Author:

D. S. Malik

Publisher:

Cengage Learning

Principles of Information Systems (MindTap Course…

Computer Science

ISBN:

9781285867168

Author:

Ralph Stair, George Reynolds

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Q12- A three phase transformer 3300/400 V,has D/Y connected and working on 50Hz. The line current on the primary side is 12A and secondary has a balanced load at 0.8 lagging p.f. Determine the i) Secondary phase voltage ii) Line current iii) Output power Ans. (230.95 V, 99.11 A, 54.94 kW)