Q1. (a) Design a stick (layout) diagram for the following static CMOS logic gate, where A, B, C, D are the logic gate inputs and O/P is the output: VDD D-d[Q8 A-Q5 B-Q6 C-d Q7 O/P CQ3 DQ4 B-Q2 AQ1 Vss Figure 1 Use dual-well, CMOS technology. Include wells, well-taps, contact cuts, routing of power and GND in your diagram. Use colour coding and/or clear and readable detailed annotations to represent the wires in the different layers. (b) The logic gate from (a) needs to drive a capacitive load of 150 fF with a rise-time and fall-time of 1.2 ns. If the length of all transistors is 0.5 μm, calculate the required widths for all P-type and all N-type MOSFETs in the logic gate to achieve the required edge-speeds. Clearly show the calculation steps of your solution. Assume VDD = 5 V, K'n = 50 μA/V², K'p = 20 μA/V²

Q1. (a) Design a stick (layout) diagram for the following static CMOS logic gate, where A, B, C, D are the logic gate inputs and O/P is the output: VDD D-d[Q8 A-Q5 B-Q6 C-d Q7 O/P CQ3 DQ4 B-Q2 AQ1 Vss Figure 1 Use dual-well, CMOS technology. Include wells, well-taps, contact cuts, routing of power and GND in your diagram. Use colour coding and/or clear and readable detailed annotations to represent the wires in the different layers. (b) The logic gate from (a) needs to drive a capacitive load of 150 fF with a rise-time and fall-time of 1.2 ns. If the length of all transistors is 0.5 μm, calculate the required widths for all P-type and all N-type MOSFETs in the logic gate to achieve the required edge-speeds. Clearly show the calculation steps of your solution. Assume VDD = 5 V, K'n = 50 μA/V², K'p = 20 μA/V²

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Q1. (a) Design a stick (layout) diagram for the following static CMOS logic gate, where A, B, C, D are the logic gate inputs and O/P is the output: VDD D-d[Q8 A-Q5 B-Q6 c-d[Q7 O/P CQ3 DQ4 B-Q2 A-Q1 Vss Figure 1 Use dual-well, CMOS technology. Include wells, well-taps, contact cuts, routing of power and GND in your diagram. Use colour coding and/or clear and readable detailed annotations to represent the wires in the different layers.
Please may you give the solution to this computer science question! Thank you
Using 6 NMOS devices, design a NMOS style of the logic gates diagram below. Label the inputs and output.
Please do part b using the Assumption
3b will upvote for correct answers
It has to be designed using CMOS logic, not with simple gates. Also, there are two more options to solve. Thank you.
A certain digital circuits designed to operate with voltage levels of -0.2Vdc and -3.0Vdc. If H= 1 =-0.2 Vdc and L =0 =-3.0 Vdc, is this positive logic or negative logic ? H=+5.0Vdc. and. L=+1.0Vdc What are the voltage levels between fall and rise times are measured? What is the value of Duty cycle H if the waveform is high for 2 ms and low for 5 ms?
Q4: Suggest a control gate drive circuit for a Triac, which is used to control a fan regulator. The gate signals should be synchronized with the input voltage. Draw the complete: 1. Circuit diagram with the load and 2. The waveform of the input and output voltages. ) Q.13 Indicate whether the following statements are correct or not then correct the incorrect statements 1) the multi pulse selected notching technique used in inverter is used to eliminate the low order harmonics and to reduce switching frequency, 2) In 3-phase half-controlled half-wave rectifier, the firing angle can be varied from 0 to 180 degrees while in 6-phase half-controlled half-wave rectifier can be varied from 0 to 150 degrees Q.14 Indicate whether the following statements are correct or not then correct the incorrect statements 1) In rectifier circuits, lower pulse number and connecting either primary or secondary of 3- phase winding in delta will reduce the harmonics content of the drawr. current 2) In…
Please may you give the solution to this computer science question in a step by step form. Thank you
Digital Electronics and Design Question a) Find the output of the gate circuit shown in the figure below and obtain the simplest expression for the output of the circuit. b) Plot the simplified function. (Use the minimum number of gates.) c) Design the CMOS circuit that implements the given function. (Use the minimum number of transistors.)
Can i have a written solution solution for better understanding?
1. (a) Implement the logic function F = {A(BC + D)}' using a 4-input static CMOS logic gate using minimum number of transistors. (b) Draw the schematic for implementing the function in (a) using ratioed logic style.