Q1: Find out the point load strength index (Is(50)) for both of the Diametral test and Axial test from the following given data as shown in Table 1: Table 1: Point load testing data Type of Test Diametral Axial Di (mm) 48 48 Df (mm) 47.0 48.0 Hi (mm) 75 76 Hf (mm) 75.0 74.0 P (KN) 22.50 23.50

Q1: Find out the point load strength index (Is(50)) for both of the Diametral test and Axial test from the following given data as shown in Table 1: Table 1: Point load testing data Type of Test Diametral Axial Di (mm) 48 48 Df (mm) 47.0 48.0 Hi (mm) 75 76 Hf (mm) 75.0 74.0 P (KN) 22.50 23.50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

What are the engineering applications of each of these tests? a. flash point test b. RTFO procedure c. rotational viscometer test d. dynamic shear rheometer test e. Bending beam rheometer testf. penetration test.
Required information For the concrete beam shown, the modulus of elasticity is 25 GPa for the concrete and 200 GPa for the steel. Take b=218 mm and d = 450 mm. Use an allowable stress of 12.5 MPa for the concrete and 140 MPa for the steel. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. Using the area of steel calculated in part a, determine the largest allowable bending moment. The largest allowable bending moment is 96.06 kN-m.
The piece of wood shown below was used in an experiment. During the test it sheared parallel to the wood grain along the dashed line. Determine the average shear stress on that failure plane for a maximum load of P= 1250 lb. The dimensions of the wooden specimen are t = 2.5 in. and L = 4 in.
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 350 MPa, determine the minimum force P required to punch the slot. Punch 745 kN 942 kN 450 kN 872 kN 677 kN Slug Plate 20 mm 75 mm Plan view of slug
Steel bars and an aluminum bar support the rigid slab as a platform as shown below. A gap A= 0.26 mm %3D exists between the aluminum bar and the slab. Neglecting the weight of the slab a (/degree celsius) 11.6x10* 23.1x10* A (mm²) E (GPa) Steel bar Aluminum bar 350 200 400 70 a) Which temperature increase AT is required to just close the spacing at the middle? (Note that the temperature increase will subject all bars) b) What are the stresses in the steel bars and aluminum bar for AT = 90 degree celsius in MPa? 1000 mm Steel Aluminum Steel
C36000 Brass Load (lbs) Cycles to failure (N) Stress (S) in (ksi) 60 21925 45.28 45 62333 33.96 40 162745 30.18 35 274145 26.40 4130CF Steel Load (lbs) Cycles to failure (N) Stress (S) in (ksi) 100 4444 75.46 80 223126 60.35 70 611424 52.80 67 2191170 50.55 Plot S-N curves for both metals using log scale and showing appropriate axes limits and labels and compare the fatigue characteristics.
A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowablestress is 250 MPa, Calculate the following:(a) Minimum required thickness of the plate. (Hint: HOLE vs FILLET) (b) Maximum allowable stress based on minimum thickness of the plate, Let K= 1.20 (c) Percent decrease on stress concentration
Situation 8: The rigid, horizontal slab is attached to two identical copper rods. There is agap A = 0.08 mm between the middle bar, which is made of aluminum, and the slab.Neglecting the mass of the slab, the temperature in in all rods by 60°C. Use the following data: Each bronze rod Aluminum rod 22. Compute the stress in bronze rod 23. Compute the stress in aluminum rod 24. Compute the deflection on the rods Bronze A (mm²) 650 480 A Aluminum a (/°C) 18.9 x 10-6 23.1 x 10-6 Bronze 850 mm E (GPa) 83 70
Question 6 (a)-Determine the natural frequency of vibration and mode shape corresponding to first and last mode of vibration for the shear building shown in following figure. N=2 ms=(IN) ksec/in kç= (200N) k/in m₁= (2N) ksec²/in k= (400N) k/in ms=(3N) ksec/in kj= (600N) k/in m₂= (4N) ksec²/in k₂= (800N) k/in m₁= (5N) ksec²/in k₁= (1000N) k/in
A hydraulic punch press is used to punch a slot in a 10-mm-thick plate, as illustrated. If the plate shears at a stress of 310 MPa, determine the minimum force P required to punch the slot. Punch 705 kN 660 kN 844 KN 904 kN O 772 KN Slug Plate 20 mm 75 mm Plan view of slug Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank Que Nume Blank View Que Multi Que Multip Que
Procedure: 1. Compression tests on specimens shall be made as soon as practicable after removal from the moist storage. A 28-day test shall be performed within +-20 hours of the 28thday. Test specimens shall be kept moist by any convenient method during the period between removals from moist storage and testing. They shall be tested in moist condition. 2. All test specimens for a given test age shall be broken within the permissible time tolerance prescribed below. TEST AGE PERMISSIBLE TOLERANCE 24 HOURS +-0.5 HOURS OR 2.1% 3 DAYS 2 HOURS OR 2.8% 7 DAYS 6 HOURS OR 3.6% 28 DAYS 20 HOURS OR 3.0% 90 DAYS 2 DAYS OR 2.2 % 3. With a clean rag or rush clean the bearing faces of the bearing blocks, test the specimens and exclusion controller (elastomeric cps). 4. Rest the specimen on the lower extrusion controller, place the top extrusion controller on the specimen, and check the spacing between the sides of the specimen and the extrusion controllers to ensure no contact between the cylinder…
Question 8 of 10 View Policies Current Attempt in Progress HO D d The extruded plastic shape has dimensions of D = 37 mm, d = 35 mm, a = 99 mm, and t = 7 mm. (a) Determine the magnitude of the horizontal shear stress at point A for a shear force of V = 365 N. (b) If the allowable shear stress for the plastic material is 800 kPa, what is the magnitude of the maximum shear force V that can be applied to the extrusion? N Answer: dik a - / 10 E ||| :