Q1: Find out the point load strength index (Is(50)) for both of the Diametral test and Axial test from the following given data as shown in Table 1: Table 1: Point load testing data Type of Test Diametral Axial Di (mm) 48 48 Df (mm) 47.0 48.0 Hi (mm) 75 76 Hf (mm) 75.0 74.0 P (KN) 22.50 23.50

Q1: Find out the point load strength index (Is(50)) for both of the Diametral test and Axial test from the following given data as shown in Table 1: Table 1: Point load testing data Type of Test Diametral Axial Di (mm) 48 48 Df (mm) 47.0 48.0 Hi (mm) 75 76 Hf (mm) 75.0 74.0 P (KN) 22.50 23.50

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: From the typical results of a UC test in Figure 1, determine the unconfined compression strength and…

A: Note:- Hi! Thank you for the question As per the honor code, We’ll answer the first question since…

Q: The shear stress acting on the failure plane is O 100 -100 O 200 -200 Question 4 The normal stress…

A: Given:Required:Shear and normal stress on the failure plane

Q: A cylindrical block is 35 cm long and has a circular cross-section 10 cm in điameter. It caries a…

A: Solved below

Q: The piece of wood shown below was used in an experiment. During the test it sheared parallel to the…

A: Shear stress is the force that causes deformation by sliding along a plane of material. When the…

Q: Load (N) Deflection (mm) 0 0 4.903034 0.000346 11.416539 0.000802 18.337648 0.001251…

A: The data you provided is from a load-deflection test on a mortar specimen. It shows how much the…

Q: 3. Sample of steel bar has 12 mm diameter after performing tension test the failure load was 57 KN,…

A: Tensile strength: Tensile strength of the steel bar is defined as the maximum tension applied on the…

Q: 10) If this material is subjected to a stress amplitude of 450MPA, approximately how many cycles of…

A: S- N Curve is a graphical representation of Stress Amplitude versus no. of cycle of reversal of…

Q: The thin rectangular plate shown is uniformly deformed such that & = +874 pɛ, ɛ, = -536 uE, and yy…

Q: Derive an epresion for the shear stress at the pipe wall when an incompressile fuid flows through a…

Q: Please help solve. Homework

A: Given Mohrs circleNormal and shear stressesTo find out Angle of failure plane

Q: Tension specimens (diameter d0 0.500 in., gage length L0 2.00 in.) made of structural materials A…

A: Given, Do = 0.5 in Lo = 2 in

Q: Calculate the corresponding depth of uniform stress block in a reinforced concrete beam 50*10 deep…

A: We have to find the value of depth of uniform stress block

Q: A cylindrical specimen 7.5 mm in diameter of an S-590 alloy (Animated Figure) is to be exposed to a…

Q: : Calculate the wheel load stress at interior, edge and corner regions of oncrete pavement using…

A: Westergaard's stress equations: Given, Wheel load, P = 4100 kg Modulus of elasticity of cement…

Concept explainers

Foundation construction

Question

Q1: Find out the point load strength index (Is(50)) for both of the Diametral test and
Axial test from the following given data as shown in Table 1:
Table 1: Point load testing data
Type of Test
Diametral
Axial
Di (mm)
48
48
Df (mm)
47.0
48.0
Hi (mm)
75
76
Hf (mm)
75.0
74.0
P (KN)
22.50
23.50

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given

VIEW

Step 2: Calculate point load strength index for diametral test

VIEW

Step 3: Calculate point load strength index for axial test

VIEW

Solution

VIEW

Step by step

Solved in 4 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

The cross section of a concrete corner column that is loaded uniformly in compression is shown in the figure. A circular pipe chase cut-outof 10 i n. in diameter r tins t he height of t he co \u m n (see figure).(a) Determine the average compression stress crr in the concrete if the load is equal to 3500 kips.(b) Determine the coordinates x and y{of the point where the resultant load must act in order to produce uniform normal stress in the column.
Qno8 solve like sample check I don't have problem for 8 . Solve problem 8 information with figure.
Please show intermediate steps including free body diagrams, equations used, problem setup etc. so that your approach can be followed.
This is a mechanics of deformable bodies problem
A rectangular strain gauge rosette was employed to determine o = 4350 psi and o = 1450 psi, as shown below. Calculate the magnitude of o, o and t if 0 = 30°. Note: A rectangular strain gauge rosette can be used to measure the strains and then help determine the in-situ stresses, we will discuss the use of a strain gauge later in the class, but it does not impact stress calculations here. y 02 01 Ꮎ
Shear box dimensions: L= 49,8 mm W = 49.6 mm 3. Prepare the lab results using the following data: Normal Load (kN) Maximum Shearing Force kN) Specimen Number 1 0.983 0.730 1.470 0.970 3 1.960 1.120 Calculations: Obtain the normal stresses and the shearing stresses for each of the specimen above in КРа Plot maximum skear stresses (peak shear stresses) vs. normal stresses and show the peak strength envelope. Determine the friction angle of the soil material.
please answer problem 2
Label which type of failure mode is associated with each of the strain profiles shown in the figure below.
a. Determine the maximum flexural compressive stress in the beam. Answer in MPa rounded-off to 3 decimal places. b. Determine the maximum flexural tensile stress in the beam. Answer in MPa rounded off to/3 decimal places
Q26 Please provide justified answer asap
A plate was subjected to a tensile force P=100 KN as shown on the figure. If the allowablestress is 250 MPa, Calculate the following:(a) Minimum required thickness of the plate. (Hint: HOLE vs FILLET) (b) Maximum allowable stress based on minimum thickness of the plate, Let K= 1.20 (c) Percent decrease on stress concentration
Angle 1 Tyx Txy x-direction stress 60OMPA(compression), y-direction stress 40MPA(compression), negative shear stress 30MPA Using your assigned point determine the following for the yz-plane: Using a Mohr circle determine the stresses on the plane of the indicated angle 1. (50°). Show al calculations. Draw the orientation of the stress block for this scenario.