Answer the following :Q1:Derive an epresion for the shear stress at he pipe wall when an incompresibl uid flows through a pipeunder pressure. Use dimensional analysis with the following significant parameter: pipe diameter D, flowvelocity V, and visconity p and density p of the fuid.

Answered: Image /qna-images/answer/4f586ac4-8d62-4060-91c2-1f845a621537.jpg

Derive an epresion for the shear stress at the pipe wall when an incompressile fuid flows through a pipe wnder presure. Use dimensional analysis wit the following significant parameter: pipe diameter D, fiow velocity V, and viscosity p and densiy p of he fuid.

Derive an epresion for the shear stress at the pipe wall when an incompressile fuid flows through a pipe wnder presure. Use dimensional analysis wit the following significant parameter: pipe diameter D, fiow velocity V, and viscosity p and densiy p of he fuid.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The figure shows the stress condition of an I-section beam at point A. With the Mohr circle method; 1-)Calculate the principal stresses, location and angle. 2-)Calculate the stress components that will affect the plane obtained by rotating the figure counterclockwise 25.
A channel-section has the dimensions as shown. Consider a cantilevered beam subjected to an end force P. L = 100 cm a) iif cross-section las is used, determine its normal stress distribution. (a) (b) b) if you stack two las sections as a box, but leave a gap between them, two sections carry = loadings with the same distribution pattern. Try express the results. (C) 2ª L 2CM дом E 2ch weld
(32 H.W Find longitudinal and hoor tensile stresses in the Wall of vessel Shown in figure, if the internal pressure. is 0.9 MPa and thickness of Wall is 6.4mm ? Ans: 6 = 42.19 MP₂ °H = 62.8 Mra 4 Also find I ?=0.67 Alir G 0.6m fot TE L = 1.8m O 7 0.6m
(47 H.WOA vod Con sists of three bars of unequal dlameters as shown in fig., find the Stress in each bar and the C longation of the rocd ? use E = 200G Va %3D Ø=4omm =30mm =20 mm 2.1W 60 1.5m 2.5m 2m
1.) A STEEL WIRE 30 ft LONG HANGING VERTICALLY SUPPORTS A LOAD OF 500 lb. 30 ft NEGLECTING THE WEIGHT OF THE WIRE, DTERMINE THE REQURIED 500 Ib DIAMATER IF THE STRESS IS NOT TO EXCEED 20 ksi AND THE TOTAL ELONGATION IS NOT TO EXCEED 0.20 in. ASSUME E = 29 x 106 psi.
Help peles, hurry
Question 5 of 15 The plate of thickness, t 5 mm, is loaded with the following stress; o, - 100 MPa, o, - -60 MPa, E- 200 GPa, v = 0.33. If a 160 mm, and b 200 minn, D. ► X A Calculate the change in thickness (mm). Select the correct response:
For the stress case given in the figure, approximate the principal plane (in degrees).
During the tensile test, experiment on a sample of mild steel, data represented in the figure below was obtained with an initial diameter (do) of 0.505 inch. At failure, the reduced diameter (d;) of the sample was 0.305 inch. Gauge Length (Lo) is 2 inches and final Gauge Length (L) is 2.625 inches. Answer the questions below: Us TR 70- 60 - Lo LyP *IR 50 - EL PL: proportimal limit EL Elastic limit UXP = 4pper yield point Lyp : Lower us : uiti mated streagth IR : Indicanteed Strengty Rupture TR: True strength Ruptue 40 AL or 8t P 30 **PL (proportimal limt) Direct strain E strain (in/in) aStress Iblinz (esi) 0.003. ogo o-200
3.) A tube with E=10x106 psi is used to support a compressive load. The maximum allowable change in length is 0.025 percent, determine (a) the maximum normal stress in the tube (b) the minimum wall thickness for a load of 1600 lb if the outside diameter of the tube is 2.0 in.
Icles Current Attempt in Progress A thin rectangular plate is uniformly deformed, as shown. Determine the shear strain yy at P. Assume a = 1190 mm, b = 590 mm, c = 1.1 mm, and d = 0.8 mm. R Answer: Shear strain yy prad. %D