Q.2. A helical torsion spring has a wire diameter of 0.038 in, outside diameter= 0.368, 8.5 coils in the body, one end 0.5 in long and other end 1.125 in long, material ASTM A401 steel. What torque would cause the spring to rotate 180 degrees. Find corresponding stress. (6) See Fig. be low

Q.2. A helical torsion spring has a wire diameter of 0.038 in, outside diameter= 0.368, 8.5 coils in the body, one end 0.5 in long and other end 1.125 in long, material ASTM A401 steel. What torque would cause the spring to rotate 180 degrees. Find corresponding stress. (6) See Fig. be low

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A shaft/hub connection transmits a torque C =60N.m. We use a rectangular key (W=14mm x H=9mm) with a length of 30mm for a 45mm diameter shaft. Calculate the force exerted on the key.Calculate the compressive and shear stress.
A cable and pulley system at D is used tobring a 230-kg pole (ACB) to a vertical position, asshown in the figure part a. The cable has tensile forceT and is attached at C. The length L of the pole is6.0 m, the outer diameter is d = 140 mm, and the wallthickness is t = 12 mm. The pole pivots about a pin atA in figure part b. The allowable shear stress in the pinis 60 MPa and the allowable bearing stress is 90 MPa.Find the minimum diameter of the pin at A inorder to support the weight of the pole in the positionshown in the figure part a.
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
A helical compression spring is wound using 4 mm-diameter Chrome-vanadium wire. The spring has an outside diameter of 28 mm with squared and ground ends, and 14 total coils: (a) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength, that is, that it is solid-safe? (b) What force is needed to compress this spring to closure? (c) Estimate the spring rate. (d ) Is there a possibility that the spring might buckle in service?
A closely coiled helical spring is made of 6 mm diameter steel wire, the mean diameter of the coil is 60 mm and there are 8 coils. Taking the modulus of rigidity as 100 kN/mm2, find the stress, in kPa, in the wire when carrying an axial load of 529N.
A split-ring clamp-type shaft collar is shown in the figure. The collar is 50 mm OD by 25 mm ID by 12 mm wide.The screw is designated as M 6 × 1. The relation between the screw tightening torque T, the nominal screw diameterd, and the tension in the screw F i is approximately T = 0.2 F id. The shaft is sized to obtain a close running fit. Findthe axial holding force Fx of the collar as a function of the coefficient of friction and the screw torque.Suppose the collar of Problem 5–80 is tightened by using a screw torque of 20 N ∙ m. The collar material is AISI 1035steel heat-treated to a minimum tensile yield strength of 450 MPa.(a) Estimate the tension in the screw.(b) By relating the tangential stress to the hoop tension, find the internal pressure of the shaft on the ring.(c) Find the tangential and radial stresses in the ring at the inner surface.(d) Determine the maximum shear stress and the von Mises stress.(e) What are the factors of safety based on the maximum-shear-stress and…
The spring of the check valve seen in the figure is mounted with a pre-stress of 12 mm and the diameter of the Spring Wire is 2.7 mm, the number of winding is 13, the slip module is 80800 N/mm?, the average diameter of the winding circle is 23 mm. If these conditions are taken into account, check the spring strength by finding out how much pressure the check valve will open at. Publication safe shear stress value is 185 N/mm? and 1 bar = 0.1 N / mm? will be taken. Ø10
Q2: Design a torsion spring with an initial torque of T, =2000Nmm and a maximum torque of T2 =8000Nmm. The minimum angular deflection is oi 10 and the maximum angular deflection is p2 =400. The spring is to be installed in a steadily operating machine.
(10) A weight of 270kg falls a distance of 1.0m & strikes a coil compression spring which absorbs the blow with a deflection of 0.3m. The mean diameter of the coils is to be 8x the wire diameter. If the allowable stress is 415MPa & the modulus of rigidity is 80GPa, find the diameter of the wire & the number of effective coils required.
A hard-drawn steel wire extension spring has a spring index Of 7.5, hook radii of r = 0.106 in and r2 0.089 in, and an initial tension of 1.5 lbf. The number of body turns is 13.5 and the uncorrected initial stress is 16.5 kpsi. From the given information: (a) Determine the physical parameters of the spring. (b) Find all stresses at ends A and B and the body torsion under the static load of 6 Ibf.
A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Say= 0.5 Sut for shear strength.)
For Hibiscus and Rose Groups A steel helical spring is wound from No. 14 music wire with a mean helix diameter of 0.6 in. The load varies continuously between 10 and 4 Ib. Find the factor of safety.