H.W (2):A helical compression spring is made of hard drawn carbon steel has a maximum permissible shear stress 902 MPa and a wire diameter of 0.94 mm. The outside diameter of the spring is 11.11mm. The ends are squared and there are 12.5 total turns. Find, The axial load which the spring can carry. 1. 2. The spring constant. The deflection that would be caused by the load. 3.

H.W (2):A helical compression spring is made of hard drawn carbon steel has a maximum permissible shear stress 902 MPa and a wire diameter of 0.94 mm. The outside diameter of the spring is 11.11mm. The ends are squared and there are 12.5 total turns. Find, The axial load which the spring can carry. 1. 2. The spring constant. The deflection that would be caused by the load. 3.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

bar AB is Q1) A homogeneous of M supported at either end by a cable as shown in figure beside. If the stress is not to exceed 75 MPa in bronze and 110 MPa in steel. And the diameter of bronze cable is 25 mm while for steel cable is 20 mm. Calculate the maximum safe mass M that can be carried by these cables. (1300) Bronze A 8m Steel
A round bar of length L. modulus of elasticity E, and weight density y tapers uniformly from a diameter of 3D at one end to a diameter 2D at the other end. If the bar is suspended vertically from the larger end, find the elongation of the bar caused by its own weight.
3) For a torsional window-shade spring shown as figure, determine the maximum operating moment and corresponding angular deflection. Given: Thickness, h : Music Wire :1.625 mm • Mean coil diameter : 25 mm • Number of active coil : 350 Spring Material Wire diameter • Factor of safety :1.5
Solve
A bus’s leaf spring has following data-Number of leaves = 15 Each leaf’s width = 15 mmThickness = 12 mmMain leaf’s span = L = 2l = 400 mm.Modulus of elasticity, E = 200 GPa.Under a static load w, the tip deflects by 40 mm. Find,i) The value of w.ii) The maximum stress.
Q3. Design a compressive helical spring which was made of alloy steel. The maximum applied load to the spring is 1000 N. The total number of the coils should be no more than 10 turns if a squared and ground ends spring used. The solid length is 60 mm. Neglecting the effect of stress concentration. What is (1) the energy stored in the spring. (2) axial deflection. (3) The mean diameter of coil. (4) The wire diameter. (5) Spring rate. If the applied load is shifted to the edge of the spring, farthest point from the centre of the spring, determine the load that the spring can carry it without failure.
A solid steel post is subjected to pure torsion. Given: -post Diameter = 65 mm -length = 2.75 m -torque = 2.4 kN-m -shear Modulus of Elasticity = 78 GPa Question: What is the Polar Moment of Inertia of the Post?
A steel helical compression spring of an average coil diameter of 16 mm with a wire diameter of 1,4 mm and active coils of 6. Assuming Gsteel as 80 GPa, predict (a) the axial load (b) the deflection (c) spring rate
What is the load carried by the spring and the maximum flexural stress?
None
A steel helical compression spring of an average coil diameter of 16 mm with a wire diameter of 1,4 mm and active coils of 6. Assuming Gsteel as 80 GPa, predict (a) the axial load (b) the deflection (c) spring rate
(10) A weight of 270kg falls a distance of 1.0m & strikes a coil compression spring which absorbs the blow with a deflection of 0.3m. The mean diameter of the coils is to be 8x the wire diameter. If the allowable stress is 415MPa & the modulus of rigidity is 80GPa, find the diameter of the wire & the number of effective coils required.