A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Ssy= 0.5 Sut for shear strength.)

A helical compression spring is made with oil-tempered wire of diameter 0.2", mean coil diameter of 2", 12 total coils, 5" free length, and squared ends. (a) Find the solid length. (b) Find the force required to compress the spring to closure? (c) Find the factor of safety against yield when compressed to the solid length. (Hint: Uses Ssy= 0.5 Sut for shear strength.)

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.5.29P: A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed...

See similar textbooks

Similar questions

A polyethylene tube (length L) has a cap that when installed compresses a spring (with under-formed length L1) by an amount ?? = (L1 = L). Ignore deformations of the cap and base. Use the force at the base of the spring as the redundant. Use numerical properties given in the boxes. (a) What is the resulting Force-in the spring, Fk? (b) What is the resulting Force in the tube, Ftl (c) What is the filial length of the tube, Lf? (d) What temperature change ?T inside the tube will result in zero force in the spring
Q.2. A helical torsion spring has a wire diameter of 0.038 in, outside diameter = 0.368, 8.5 coils in the body, one end 0.5 in long and other end 1.125 in long, material ASTM A401 steel. What torque would cause the spring to rotate 180 degrees. Find corresponding stress. (6) See Fig. below
Don't give handwritten
Find: spring rate, force at solid length,check for buckling,coil clearance and hole diameter
Two coaxial closed coil springs make up a standard compound helical spring. When both springs are unloaded, they are not of equal length. If each spring's working stress is to be the same. The wire material has an 80 GPa modulus of rigidity. Find the diameter of steel wire for inner spring and stiffness of inner spring. Also find the stiffness of the compound spring. Outer spring a: Mean coil diameter = 100 mm No. of turns = 15 Wire diameter = 12.5 mm Inner spring b: mean coil diameter = 75 mm No. of turns = 20
A helical compression spring is subjected to a maximum force, Fmax of 1250 N. The deflection of the spring corresponding to the maximum force should be approximately 30 mm. The spring index is 6. The allowable shear stress is 350 MPa and the modulus of rigidity is 81 370 N/mm². Design the helical spring by calculating the wire diameter, mean coil diameter, number of active coils and the total number of coils. State all assumptions and decisions in your design.
Design a helical spring to be used in spring balance with a wire diameter of 6mm and the outside diameter should be limited to 66mm. if the permissible shear stress of the spring material is 325 N/mm? and the Modulus of rigidity is 85kN/mm?. a) Compute the deflection of spring per active turn and the axial load on the spring considering the effect of curvature, take Wahl's factor as Kw= 1.1 b) Calculate the value of axial load neglecting the effect of stress factor. **Note: Please upload your handwritten working/solution to the link provided. The value of Mean diameter of the spring in mm . The Spring Index is. Shear stress factor, neglecting curvature effect . Deflection per active turn in mm Axial Load W in N .. Axial Load W in N. considering effect of curvature .
Kindy answer correctly. Please show the necessary steps (the template is provided)
A spring made from music wire ASTM 228 steel has the following data:Free length=1.75” Outside diameter=0.561”Wire diameter=0.055” Applied load= 14 lbEnds=square and ground both ends hingedNumber of coils=10 G=11.85 x 106psi E= 30 Mpsi Findspring rate, force at solid length,check for buckling,coil clearance and hole diameter
PROBLEM:2 A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter of 12.5 mm and 15 active coils. Find (a) Stiffness of the spring (b) solid length. Assume that the ends are squared and ground. Take modulus of rigidity as 0.85x105 N/mm2.
A helical compression spring is wound using 4 mm-diameter Chrome-vanadium wire. The spring has an outside diameter of 28 mm with squared and ground ends, and 14 total coils: (a) What should the free length be to ensure that when the spring is compressed solid the torsional stress does not exceed the yield strength, that is, that it is solid-safe? (b) What force is needed to compress this spring to closure? (c) Estimate the spring rate. (d ) Is there a possibility that the spring might buckle in service?
When a coil spring with a spring rate of 150 lb/in. is compressed 1.5 in., the coils are closed. The allowable shear stress is 60,000 psi, the spring index C = 6, the ends are squared, and G = 12 x 106 psi. Calculate: a. The required wire diameter d, b. The required coil diameter D, %3D C. The required number of coils, d. And the closed length of the spring.