Q-5 Wall thickness of a thin cylinder shell of 800 mm internal diameter is 10 mm. length of the cylinder is 2m. if the shell is subjected to an internal pressure of 1.5 MPa, determine the maximum shear stress.

Q: Convert 3 centimetres (cm) to millimetres (mm)

A: Given data: Unit = 3 centimetre Need to convert into millimetre.

Q: isc SC

A: given:discuss how the cylindercal square is used?

Q: How many balls of 30 mm diameter fit in a volume of 1.91 m^3

A: Given data: ● The total volume of space:  V = 1.91 m3 ● The diameter of the single ball: d = 30 mm =…

Q: 꾸 A solid that has two parallel and equal polygons as bases is called what? Select one: O A. A cube…

A: A solid that has two equal polygons that are parallel as bases is known as prizm.

Q: how to determine the volume of a flour using scientific method.

A: It is very important to measure the volume of the flour when any recipe is prepared in the kitchen.…

Q: What is the depth of the liquid from the free surface if the pressure at a point from the surface is…

A:

Q: What are 1-, 2-, and 3-point perspectives? Draw cubes of different sizes using 1-, 2-, and 3-point…

A: Approach to solving the question: drawing, constructing of answer Detailed explanation: Examples:Key…

Q: 3. Refer to figure 2. Assume the beam's mass holding the objects is negligible, calculate the center…

A: Centre of mass is defined as the point of location on the beam where it is assumed that all the mass…

Q: Solve for the y-component (in mm) of the centroid if that a=2.3, b=2.4, c=4.8, d=8.7, and r=1.5. All…

A:

Q: 5. What is the size of pattern? The size of pattern is different than size of casting b. The size of…

A: Pattern is defined as the replica of the casting to be produced which when placed in mould leads to…

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Compute the coordinates of the centroid (x, y) of the area shown. y

A:

Q: Identify the following sectioning views (a, b, and c). a O Removed, Revolved and Removed O All…

A:

Q: A quart of water weighs 7.1 lb.  Determine its mass(slugs) Choices are: A. 0.13 B. 0.17 C. 0.26 D.…

A: Given, weight = 7.1 lb

Q: The rectangular plate has a semi-circle cut out as shown. The x' and y' axes go through the centroid…

A:

Q: Locate the centrod.) of the shaded are Express your answers using three significant figures…

A:

Q: ight has a vo

A:

Q: Solve for the x-component (in mm) of the centroid if that a=2.2, b=2.2, c=4.6, d=8.5, and r=1.2. All…

A: FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: How many balls of 70 mm diameter fit in a volume of 1.91 m^3

A: Given data Diameter of ball = 70 mm Total volume = 1.91 m^3 Brief introduction First determine…

Q: Find the volumes of the solids generated by revolving the shaded regions The x-axis The y-axis

A:

Q: A rectangular tank measures 1.2 meters long, 1 meter wide and 2 metres high. What is the volume, in…

A: Note:As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Obtener el centroide de la siguiente figura. -300 mm 150 mm 150 mm 75 mm 100 mm 100 mm

A:

Q: The diagram shows a 1 cm3 block that is divided into cubic millimetres. How many mm are there along…

A:

Q: A. Which of the following gives the area in square meters. B. Which of the following gives the x…

A:

Q: The following area is a cross-section of a structural member. The coordinate for the location of the…

A: To find: The coordinate for the location of the centroid. Free Body diagram :  Redraw the image with…

Q: Q3/ Determine the resultant of the force system with respect to the point (A)

A:

Q: b) Describe the following terms. Use a diagram if necessary. i. Neutral axis of a beam ii. Centre of…

A: GIVEN DATA THREE TOPIC GIVEN WE HAVE TO DEFINE IT WITH DIAGRAM

Q: need help finding dimension x and y in the casting shown 2.80 cm 5.20 cm 6.00 cm 2.50 cm E 7.20 cm

A: Draw a diagram for the given problem.

Q: A shift lever ball has diameter 2.535 in. What is its volume in cubic inches

A: Given   Diameter, d = 2.535 in       Radius, R = 1.2675 in Find    Volume, V

Q: centroid location of the transformed section in the vertical direction. Enter your answer in mm to 1…

A:

Q: c) The bore of each cylinder in a six-cylinder car engine is 52 mm and the stroke for each piston is…

A:

Q: 21. One of the following surface plate show that surface is flat at one end but becomes increasingly…

A: Given: Let us consider the given figures, To find: One of the following surface plates depicts a…

Q: Required: Letter J

A:

Q: many hours did the carpenter work on the job? 6. What is the area of a rectangular floor that is…

A: Q.6 Given data as per question Length of floor = 7’-3” Width of floor = 4’-2”

Q: Locate the centroid (7, y) of the area.(Figure 1) Part A Locate the centroid a. Express your answer…

A: given; centroid ;x¯=?y¯=?

Pressure Vessels

The term pressure vessel refers to a closed container that contains gas or liquid at a different pressure than environment pressure. The pressure vessels have a wide scale of applications in our day-to-day lives and other industrial places. Some common examples of pressure vessels are gas cylinders, autoclaves, compressor vessels, etc.