How did 6650 mm2 come from please show the work.

Q: Build the following part. Report the mass in pounds. Assume all dimensions are in inches. The…

A: It is asked to find the mass of the model from the given dimensions Material: Vanadium

Q: How much scrap pipe will be left if a 13-ft 6in. piece is cut out of a 20-foot length of pipe?

A: total length of pipe=20'cut piece length of pipe=13'6"

Q: What is the maximum thickness dimension allowed on the part?

A:

Q: If the part was cut by this plane, what would the resulting remaining face look like?

A: Section planes in SketchUp cut a model along a plane so you may look within it without altering…

Q: Determine the relative roughness of cast iron pipe with inner diameter 3.1 inches. Your answer…

A: Given Internal Diameter (D) = 3.1 inches                                    = 3.1 * 25.4 mm…

Q: The cord of a bow string drill was used for

A: The bow drill was used in ancient period.

Q: of bell wire in inventory is to be approximated by weight. The weight of the wire is listed in the…

A: Weight of full spool = 2038=1638 ouncesEmpty Spool weight = 114 = 108 ounces

Q: 10 1 R6 1 10 20 50 30 R10 -5 X 45.00° 50 1 1 5 15 5 R30 110 R5 55 20 R6 7 8 60 30 -60 店 06-4 holes…

A: Step 1: First create following top view and extrude it up to required depth i.e. 60 mm

Q: 1.00 1.38 3.38 38 2.00

A: Select the correct statement about the notation circled in green and marked as letter D. Assume all…

Q: A pneumatic system is producing 50 lb/in.2 of gauge pressure. A cylinder is needed to press an…

A: The force produced by the pneumatic cylinder can be calculated using the formula: Force = Pressure x…

Q: Is 2.0cm3 of aluminum same as 2.0cm3 of lead

A: According to the given data, the volume of the aluminum object is 2.0 cm³  and the volume of the…

Q: where do you get the form factor (y=.337) from? Please.

A: Form factor for full depth 20° at 24 teeth can be taken from standard table. I have provided the…

Q: re did you get 1 for m from???

A: Given data as per questionInitially air containsFirst Phase1P1=30 lbf/in2T1=540°FV1=4 ft3Second…

Q: b) The bore diameter of each cylinder in a six-cylinder four-stroke internal combustion engine is 32…

A: Find  Mean effective pressure Indicated Power

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: Calculate the volume (in ft) of material used in making 350 ft of 2 in. type L copper tubing.

A: Given that, From the table of type L copper tubeFor a 2 in. in nominal size tube:Outside diameter,…

Q: Build the following part. Report the volume in in^3. Assume all dimensions are in inches. A = 2.62 B…

A:

Forming and Shaping

Metal forming is a category of metalworking process through which the material can be given the desired shape and size by subjecting it to plastic deformation, where the component undergoes bulk deformation process upon application of loads. Unlike the shearing and machining process, the material does not undergo up to a failure point as indicated in the stress-strain curve. Hence, the stresses induced during the forming process are greater than yield strength but less than the failure strength of the material. The process does not lead to the loss of material, so it can be said to be an economical process. During forming, the material is subjected to tensile forces, compressive forces, bending, and shearing loading conditions. The material should possess the property of ductility to undergo the forming process.