Vickers microhardness tests have been conducted on a brass specimen. For an applied load (P) of 1000 g, the diagonal dimension of the indentation is measured under a microscope to be 0.1060 mm. What is the expected tensile strength of the brass specimen? All six sections of the solution are needed.

Q: Dimension is 3/4” scale is 2”=1” what is the distance?

A:

Q: Draw the following using the given figure: 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3.…

A: Find 1. 45-degree CAVALIER 2. 45-degree CABINET OBLIQUE 3. Isometric Drawing

Q: how o create all parts list after the drawing ?

A: Given question: how to create all parts list after the drawing ?

Q: Given the isometric drawing, draw the multiview projection. The multiview projection of the glass…

A: Draw the isometric view.

Q: I keep being told this requires me to make my own drawing, but that is incorrect. The instructions…

A:

Q: Please look at pic. Please help, I don't get part b. Thanks

A:

Q: I have three parts that I need answered pertaining to the print provided below.   Do the dimensions…

A: It is mentioned in the drawing specification that “dimensions and tolerances apply before the…

Q: a= 15.0 in, b= 7.0 in, c= 12.0 in, and d= 12.0 in.,(e = 3.0 in. horizontal), Draw the kinematic…

A: Given mechanism:                           Given datalength of link a = 15 inlength of link b = 7…

Q: Create a free hand isometric drawing of the three objects

A: Free hand isometric drawing of all three components are drawn below...

Q: Hi, please complete the last three subparts of this question.

A: To calculate the rate of heat transfer, to derive and to calculate the mass flow rate of water, flow…

Q: With reference to the drawing callout in figure 5 below, which part(s) would 'pass' or 'fail' along…

A: Data given-  Dimensions of standard size  0.25±0.01 So tolerance is equal to 0.02  And the upper…

Q: Can you show the work but written out please so I can see the steps better.

A:

Q: Thank you for your help. I was able to get them all but can't get F correct. Could you help me with…

A:

Q: 1.3 Please help. Written on paper not typed on computer or keyboard please. Need help both…

A: Sure, based on the information provided in the text accompanying the image, the angle between lines…

Q: the isometric drawing has to be in 30 degree angle or vertical

A: It is asked to describe whether the isometric drawing has to be at 30 degree angle or vertical

Q: Draw an orthographic(three-view drawing) of the four objects including front, top, and right views

A:

Q: What is the worst-case distance between the bottom surface of the slot and the botto surface of the…

A: Given drawing

Q: As shown, a section of a roller coaster track (Eigure 3) follows the form of y = (2/3)x¹.5 Locate…

A:

Q: Please show all the steps, thanks

A:

Q: Write the Column Formulas?

A: Types Critical load Both ends hinged π2EIl2 one end hinged other end fixed 2π2EIl2 both ends…

Q: 7. Using the drawing below as a reference, Change "101" refers to which feature on the drawing? A.…

A: according to the drawing

Q: number d and e?

A: To solve this question, we will use the moment equilibrium equation which is mentioned in the…

Q: Please turn this into 3d drawing, measurements are not important.

A: According to the question We need to find 3-D model of the drawing

Q: How to draw 4/5 × 2/3 on a model

A: A mixed fraction is a fraction that has both a quotient and a remainder. 2 1/3, for…

Thermal Properties of Materials

In mechanical engineering, the thermal property is represented as the physical quantity that is relevant to the application of heat. The thermal properties are evaluated by variations in any specific material due to low heat or high heat. The quantities that influence the thermal property of the materials are mass, density, temperature, and many others.