show the step by step by constructing this using Solidworks. pls

Q: which is given. What are the x and : coordinates of the bracket's mass cen- ter? (The angle 0 in the…

A: To Find :  The x and z coordinate of the bracket mass . Given :  The total number of hole is n=4 The…

Q: 127 157 18 11 0) D 24y

A: Let's name the marked lengths in the given figure for calculation purpose.

Q: Q/1-B: For the solid geometry shown in figure below, construct the required CSG tree.

A: Find Construct the required CGS tree.

Q: In the figure shown, compute the following : 75 mm 75 mm E 75 mm-

A: Given Shaded area To find Centroid X axis Centroid Y axis

Q: Question 2) Forces of F1 =8 kN in the z direction from the point B in the figure, F 2 =6 kN in the z…

A:

Q: please use Mohr's circle for the solution

A: Use Mohr's circle, The state of stress at a point is shown on the element. To find-  (a) The…

Q: 3. Refer to figure 2. Assume the beam's mass holding the objects is negligible, calculate the center…

A: Centre of mass is defined as the point of location on the beam where it is assumed that all the mass…

Q: Q. 2 Find the position of centroid with respect to given X and Y axis of shaded portion in the…

A: Given Shaded area To find Centroid

Q: ده ))

A: The mass of each piece is m.

Q: Can you please draw Mohr's circle for the solution above?

A: Given that, σx=350 MPaσy=230 MPaτxy=-480 MPa

Q: Compute the coordinates of the centroid (x, y) of the area shown. y

A:

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First 3. angle…

A: First draw the given front view and side view of casting.

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A:

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: Let's work through the calculations for the given L-shaped object.### Part a: Finding the x-centroid…

Q: A chemistry graduate student is designing a pressure vessel for an experiment. The vessel will…

A:

Q: Conversion of units: A pyramid has a height of 500 ft, and its base covers an area of 15.0 acres…

A:

Q: A shell of diameter = 600 mm Height of the shell= 300 mm Height with corner radius=D0.6 mm It is…

A: Given: Diameter of shell, d=600 mmheight of the shell, h=300 mmHeight with corner radius, r=0.6 mm

Q: Please help. Written on paper not typed on computer or keyboard please. Need help on all questions.…

A: ## Moment of Inertia Calculations (by hand)**Given:*** a = 22 ft* y = x^2 (for part a)* y = x (for…

Q: please calculate at least 3 decimal places a) Draw a sketch where you replace the distributed…

A:

Q: JC BRA JC Ma = 2.5kg BRD BAD Mb=7kg Given that: The line of force for BRD is 5cm. Distance JC to Ma…

A: Mass, Ma= 2.5 kg Distance between JC and Ma, a= 16 cm Mass,Mb= 7 kg Distance between JC and Mb, b=…

Q: 1. show all steps in detail, units and formulas please.

A:

Q: (1) A rod of length L has a small square cross section b²; the density of the material is p. Just by…

A:

Q: Q5: For the below shaded area, calculate kand Kr 130 mm 30 mm 30 mm 40 mm 40 mm

A:

Q: Please find the centroid and Ixx for the following shapes. Show all work with neat handwriting and…

A:

Q: Q1: Find the volumes of the solids generated by revolving the shaded regions (revolving about…

A: solid generated is divided into slices along axis they are presented by washer having thickness d…

Q: Hello, I need help with the answer of 3.14 from the picture, please.

A:

Q: PS Find Ter, Cower , P for Figure lower 1 below 9, 一E 2.

A:

Q: Draw isometric view of casting, two views (FV and SV) of which are shown in figure in First angle…

A: Given question: Draw isometric view of casting, two views (FV and SV) of which are shown in figure…

Q: Please calculate the moment of inertia values for each figures according to defined rotation axises.

A: Given Data: The radius of the sphere is R. The length of the rod is L. The masses of the sphere and…

Q: OK, so the EA = 108 N, Length (L) = 13 m, and the angle is 22.6. What now?

A: Here you are asking about what to do if the EA = 108 N, Length (L) = 13 m, and the angle is 22.6…

Q: The above part of the casting component is spehere .sketch carefully the isometric view  Also…

A:

Q: i dont really understand the explanation of part b or how they used trigonometry to get that. can…

A: Part (b) For the rectangular trough:The height is derived from the formula for the volume of a…

Q: Compute the coordinates of the centroid (,) of the area shown. Hint: Use composite with shapes in…

A: The step by step solution is provided below

Q: Find Ix for the shape below:

A: To determine: The moment of inertia of the shape about X axis. Image: Consider a image below:

Q: a) locate the centroid of area given in figure  b) calculate the second moments of area give in…

A: Given:   The cross section is shown below:

Q: K- 12-7mm 113 |不 17.57 mm mm 不可 K- 197-75mm 「下

A: (a) Centroid

Mechanical Drawings

A mechanical drawing is described as a technical drawing created by engineers following standard layout conventions, terminology, interpretation, and many other factors. It is also known as an engineering drawing.