Pump Horsepower in Brine System. A pump pumps 0.200 ft3/s of brine solution having a density of 1.15 g/cm3 from an open feed tank having a large cross-sectional area. The suction line has an inside diameter of 3.548 in. and the discharge line from the pump a diameter of 2.067 in. The discharge flow goes to an open overhead tank, and the open end of this line is 75 ft above the liquid level in the feed tank. If the friction losses in the piping system are 18.0 ft lbf/lb m, what pressure must the pump develop and what is the horsepower of the pump if the efficiency is 70%? The flow is turbulent.

Q: Question 5: The pump shown below delivers a head of 50 m to the water through 30 cm diameter with…

A:

Q: The variation of pump head, efficiency, and required ENPY parameters with flow rate obtained from…

A:

Q: Situation: Water is pumped from one tank to another. Find: r/d = 1, D = 10 in, L = 50 ft. f2 =…

A: Since the pipe has constant area of cross section through out.…

Q: 1) A plugged dishwasher sink with the dimensions of 16 in. ✕ 20 in. ✕ 7 in. is being filled with…

A: As per our company guidelines, we are allowed to answer only the first question in case of multiple…

Q: A storage tank has hot water. This water at a temperature of 85 °C is pumped to a 600 cm height at a…

A:

Q: A pump draws 20 m3/h of water having a density of 1000 kg/m3 from the open storage feed tank to an…

A:

Q: Provide one question and its solution involving an external flow of fluid .

A:

Q: You want to pump water at a rate of 2 m^3/s from the lower to the upper reservoir. What type of pump…

A: Given   Flow rate, Q = 2 m3/s       Speed, N = 600 rpm      Friction, f = 0.01      Length, L = 20 m…

Q: As part of a processing of biofuels, water is pumped into a circular tank with a diameter D₁, as…

A: For the solution refer below images.

Q: Water is filled into a circular tank (inner diameter 1 m) from two inlet pipes as shown. The…

A: Inner diameter of the tank, Volumetric flow rate at inlet 1, Let the volumetric flow rate at inlet 2…

Q: Two vertical circular cylindrical tanks are connected near the bottom by a short tube having a…

A:

Q: or this system and Ywater = 62.4 Ib/ft³, what is the (a) total horsepower required by owor…

A: Given

Q: Water is pumped through a vertical 2-in. new galvanized-iron pipe to an elevated tank on the roof of…

A:

Q: 1 J A pump is used to circulate a water from lower Tank to upper tank. The height difference between…

A: Given data: The height difference between the free surface is h=5 m The total head losses in the…

Q: onsider the hydropower schematic shown below with a lake of 70m elevation above a turbine house.…

A:

Q: What is the velocity of the pipe center (m/s)? Given that h3%-88.3 cm h3 h2 =7 cm h =3 cm] Water

A: hps=88.3+7hps=95.3 cm or 0.953 mhp=7 cm or 0.07 m apply bernoulli's equation between 1 and…

Q: As seen in the figure, the vacuum pump provides air flow in an insulated pipe with a cross section…

A: Given data, Calculating Mach Number at section using the given relationship: - Hence, the Mach…

Q: You are working as a trainee engineering in a company ABC, is the leading manufacturing company for…

A:

Q: Develop an introduction to a fluid pumping project, which aims to experimentally find the…

A: Step 1: Understand the project scope by finding the characteristic curves of the pump for your…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.