Problem#4* - Design the optimal location of triggering flow transition to maximize the cooling efficiency of a flat plate. The boundary layer associated with parallel flow over an isothermal plate may be "tripped" at any x- location by using a fine wire that is stretched across the width of the plate. Determine the value of the critical Reynolds number Rex,c, that is associated with the optimal location of the trip wire from the leading edge that will result in maximum heat transfer from a warm plate to a cooler fluid. Assume the Nusselt number correlations provided in the text for laminar and turbulent flows apply in the laminar and turbulent regions (mixing laminar and turbulent flows, CASE C in your handout notes), respectively.

Problem#4* - Design the optimal location of triggering flow transition to maximize the cooling efficiency of a flat plate. The boundary layer associated with parallel flow over an isothermal plate may be "tripped" at any x- location by using a fine wire that is stretched across the width of the plate. Determine the value of the critical Reynolds number Rex,c, that is associated with the optimal location of the trip wire from the leading edge that will result in maximum heat transfer from a warm plate to a cooler fluid. Assume the Nusselt number correlations provided in the text for laminar and turbulent flows apply in the laminar and turbulent regions (mixing laminar and turbulent flows, CASE C in your handout notes), respectively.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A tube bank uses an aligned arrangement of 10-mm-diameter tubes with ST = SL = 20 mm. There are 10…

Q: Step 4 X Your answer is incorrect. What is the free convection heat transfer coefficient on the top…

Q: B- Thin-walled tube is maintained at 100°C with a 50-mm-diameter for the surface. In one case air is…

Q: (a) If the chip temperature may not exceed 80°C at any point on its surface, what is the maximum…

Q: An airstream of speed 160 m/s and temperature 3000 K travels on the inside of a 30 cm I.D. steel…

A: Solution: Given Data: V=160 m/sTa=3000 Kd=30 cmt=2.5 mms=6.1 mmu=10 m/sTl=15oCP=140 kPa To Find:…

Q: A cylinder (20 mm in diameter and 100 mm long) is heated internally by an electrical heater and is…

A: Given; Cylinder diameter, D=20 mm=0.02 m Cylinder length, L=100 mm=0.1 m Air velocity, V=20 m/s Air…

Q: An insulated steam pipe is used to transport high-temperature steam from one building to another.…

Q: An L1-m-long vertical copper tube of inner diameter Di nm contains liquid water at Tw=0°C. On a…

A: Given-Information:- L = 1 m Di = 21 mm = 0.021 mt = 2 mm = 0.002 mTw = 0°C = 273 K V = 3m/sT∞ =…

Q: Consider two cases involving parallel flow of dry air at V = 5 m/s, T=45°C, and atmospheric pressure…

Q: A tube bank uses an aligned arrangement of 15-mm-diameter tubes with S = S = 30mm. There are 10 rows…

A: The diameter of tube is The number of row is The number of tubes in each row is The outer…

Q: Codfish fillets originally at 10 °C are packed to a thickness of 102 mm. Ice is packed on both sides…

Q: T3=0°F. Wall -T₂ = 61°F -T₁ = 69°F Surface temperatures of plastic panel - Plastic panel has thermal…

A: Hi, you have submitted 2 questions and the first question seems incomplete because diagram and…

Q: Atmospheric air at 275 K and free stream velocity of 20 m/s flows over a 1.5 m long flat plate…

A: The mean film temperature can be determined as, The properties of air at mean film temperature can…

Q: A thermocouple is initially at temperature of T, and it is used to measure the temperature of air…

A: From conservation of enery, rate of change of internal energy due to temperature change is equal to…

Q: A preheater involves the use of condensing steam at 100°C on the inside of a bank of tubes to heat…

Q: Find the Average Nusselt number equation

A: Step 1:Step 2:Step 3:Step 4:

Q: Required inform Oil flow in a journal bearing can be treated as parallel flow between two large…

Q: Water at a temperature of T = 25°C flows over one of the surfaces of a steel wall %3D (AISI 1010)…

Q: 3.120 What is the convection mass transfer coefficient asso- ciated with fully developed atmospheric…

A: Given-Information:-Temperature, T = 27°C = 300 KMass, m = 0.04 kg/sDiameter, d = 50…

Q: A flat plate of width 1 m and length 0.2 m is maintaine at a temperature of 32°C. Ambient fluid at…

Q: Stainless steel 316 pin fins are designed for use in industrial cooling. The fins will be subjected…

Q: Problem 2 Consider forced convection of a liquid metal (Pr<<1) over a horizontal flat plate subject…

A: The velocity profile is uu∞=1 The temperature distribution is T-TsT∞-Ts=yδt

Q: In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as…

Q: Oil flow in a journal bearing can be treated as parallel flow between two large isothermal plates…

Q: Handwrite

A: To solve this problem, we need to determine the ratio of the heat transfer coefficient averaged over…

Question

Problem#4* - Design the optimal location of triggering flow transition to maximize the cooling
efficiency of a flat plate.
The boundary layer associated with parallel flow over an isothermal plate may be "tripped" at any x-
location by using a fine wire that is stretched across the width of the plate. Determine the value of the
critical Reynolds number Rex,c, that is associated with the optimal location of the trip wire from the leading
edge that will result in maximum heat transfer from a warm plate to a cooler fluid. Assume the Nusselt
number correlations provided in the text for laminar and turbulent flows apply in the laminar and turbulent
regions (mixing laminar and turbulent flows, CASE C in your handout notes), respectively.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Objective

VIEW

Step 2: Critical Re calculation

VIEW

Solution

VIEW

Step by step

Solved in 3 steps with 4 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An oil preheater consists of a single tube of 10-mm diameter and 5-m length, with its surface maintained at 180°C by swirling combustion gases. The engine oil (new) enters at 70°C. What flow rate, in kg/h, must be supplied to maintain an oil outlet temperatur of 105°C? What is the corresponding heat transfer rate, in W? m = kg/h W
Consider a flat plate placed inside a wind tunnel, and air at 1 ATM and 20°C is flowing with a free flow velocity of 60 m/s. What is the minimum length of the plate needed for the Reynolds number to reach 2 × 107? If the critical Reynolds number for external flow is 5 × 105, what type of flow regime would the airflow experience at 0.2 m from the leading edge? I need the solution from fundamental concepts of how the heat flow behaves in the system
In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at 0.21 m/s through a straight thin-walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform temperature profile, what is the surface temperature at the tube exit? Fluid properties may be approximated as p = 1000 kg/m³, c, = 4000 J/kg-K, µ = 2x 103 kg/s-m, k = 0.8 W/m-K, and Pr = 10. Determine the required heat flux, W/m². q! = i W/m? Determine the surface temperature at the tube exit, in °C. i °C S,0
Heat transfer. Show all steps for solution
A tube bank uses an aligned arrangement of 15-mm-diameter tubes with ST = S = 30 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 7 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m? i 89 kW/m
2.0 Engine oil at 100°C and a velocity of 0.25 m/s flows over both surfaces of a 0.8-m-long flat plate maintained at 20°C.Determine:(a) The velocity and thermal boundary layer thicknesses at the trailing edge.(b) The local heat flux and surface shear stress at the trailing edge.(c) The total drag force and heat transfer per unit width of the plate.
Water flows in a duct having a cross-section of 10x20 mm with a mean bulk diameter of 15.56 deg C. If the duct wall temperature is constant at 60 deg C and fully developed laminar flow prevails. a.) Calculate the heat transfer coefficient, h in W/m2-deg Cchoices: (405, 305, 151, 252) b.) What is the thermal conductivity of water at the given temperature, k in W/m-deg Cchoices: (0.604, 0.6, 0.585, 0.595) c.) Calculate the heat transfer rate per unit length in W/mchoices; (605, 366, 505, 404)
IMPROVEMENT WITH RADIATION SHIELD. A shield having an emissivity of 0.1 Example 8.13 is placed around the thermometer in Example 8.12 such that the area ratio A/A, is 0.3. The temperature indicated by the thermometer under these conditions is 5°C. The convection heat- transfer coefficient is assumed to be the same, and the shield may be assumed essentiallv to surround the thermometer. Calculate the true air temperature under these circumstances. And find estimate its uncertainty? h = 10 W/m - °C E, = 0.1, A = 0.3, A, E = 0.9, T, = 273 +5 = 278 K, T, = 263 K