A cylinder (20 mm in diameter and 100 mm long) is heated internally by an electrical heater and is subjected to a cross flow of air in a low-speed wind tunnel. Air velocity and temperature were maintained at V= 20 m/s and 30 °C, respectively. The average cylinder surface temperature was determined to be T = 130 °C. Using the correlation by Zukauskas, estimate the heat transfer rate per unit length?

A cylinder (20 mm in diameter and 100 mm long) is heated internally by an electrical heater and is subjected to a cross flow of air in a low-speed wind tunnel. Air velocity and temperature were maintained at V= 20 m/s and 30 °C, respectively. The average cylinder surface temperature was determined to be T = 130 °C. Using the correlation by Zukauskas, estimate the heat transfer rate per unit length?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: Air at atmospheric pressure and a temperature of 25°C is in parallel flow at a velocity of 5 m/s…

Q: (a) If the chip temperature may not exceed 80°C at any point on its surface, what is the maximum…

Q: Water at a temperature of T∞ = 25°C flows over one of the surfaces of a steel wall (AISI 1010) whose…

A: Given data Ks=61W/mkT=110+502=80=353kKf=0.628w/mk

Q: You are using hard chromium electroplating on a sphere. Air at a temperature of 18°C (P = 1 atm) and…

Q: A long, cylindrical, electrical heating element of diameter D = 14 mm, thermal conductivity k = 251…

A: Note that the initial surface temperature is not given in the question, so I have taken the film…

Q: Metallic cylinder 10 mm in diameter maintained at 50 °C with the engine oil fluid in a cross flow…

Q: Experiments have been conducted to determine local heat transfer coefficients for flow perpendicular…

A: The height of wall is The wide of wall is The velocity of air is The temperature of air is

Q: 4. Air at 25°C blows over a heated steel plate with its surface maintained at 200°C. The plate is 50…

A: Given data Convective heat transfer coefficient = 20W/m2K Thermal conductivity = 45 W/mK Air…

Q: KNOWN: Variation of local heat transfer coefficient with .x. Length of plate. FIND: Ratio of heat…

A: Step 1:

Q: The scientists working on Mars rover want to know what is the heat transfer from the solar panels of…

Q: Water at 15.6 °C flows across a 20- cm-square plate with a velocity of 2 m/s. A thin strip, 5 mm…

A: This question is solved with the help of the law of convection. It states that heat transfer by…

Q: Liquid at 23° C flows at 1.5 m/s over a smooth, sharp-edged, flat surface 10 cm in length which is…

Q: A flat-bottom barge is towed on a water surface at 2.57 m/s. The barge is 3.66 m wide and 6.10 m…

A: Given Data The velocity of the barge, V=2.57 m/s Width of the barge, b=3.66m Length of the barge,…

Q: Air at 305 K flows at 4 m/s over a flat plate at 350 K. The air properties are as follows: density…

A: The objective of the question is to find out the distance from the leading edge where the flow…

Q: Water at a temperature of T = 25°C flows over one of the surfaces of a steel wall %3D (AISI 1010)…

Q: Consider convective cooling of a two-dimensional streamlined strut. Rather than conducting…

Q: Determine the maximum allowable uniform heat flux, in W/m², that may be imposed at a wall heating…

A: To Find : The maximum allowable uniform heat flux Given : The ambient temperature is TThe maximum…

Q: For laminar free convection flow on a vertical plate, a popular correlation 1/4 is Nu, = CRa,4.…

A: The equations are given by,

Q: Heat transfers Water (T= 10 C, , k=0.644 W/m.C, υ = 5.54× 10^-7 m2/s, Pr=3.55), flow over plate 1m…

Q: Consider water at 27°C in parallel flow over an isother- mal, 1-m-long flat plate with a velocity of…

Q: Consider two cases involving parallel flow of dry air at V = 3.5 m/s, T = 45°C, and atmospheric…

A: The thermal boundary layer is the flow zone over the surface where temperature change in the…

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Heat transfer. Show all steps for solution
KNOWN: Expression for face-averaged Nusselt numbers on a cylinder of rectangular cross section. Dimensions of the cylinder. FIND: Average heat transfer coefficient over the entire cylinder. Plausible explanation for variations in the face-averaged heat transfer coefficients. SCHEMATIC: Air V = 10 m/s T = 300 K c = 40 mm ASSUMPTIONS: (1) Steady-state conditions, (2) Constant properties. d = 30 mm
A long, cylindrical, electrical heating element of diameter D = 14 mm, thermal conductivity k = 251 W/m · K, density p= 2,805 kg/m3, and specific heat cp = 903 J/kg · K is installed in a duct for which air moves in cross flow over the heater at a temperature and velocity of 30°C and 9 m/s, respectively. (a) Neglecting radiation, estimate the steady-state surface temperature when, per unit length of the heater, electrical energy is being dissipated at a rate of 1,033 W/m.
PLEASE ANSWER COMPLETELY AND CLEAN FOR AN UPVOTE!!
Air at 305 K flows at 4 m/s over a flat plate at 350 K. The air properties are as follows: density =1.1 kg/m3, viscosity =18.1×10−6 Pa.s, specific heat capacity =1005 J/kgK, and thermal conductivity =0.024 W/mK. The velocity and temperature profiles are assumed to be linear, giving the local Nusselt number to be Nux = 0.289 Rex1/ 2Pr1/3. The flow will become turbulent at a Reynolds number of 5×105. Assume the width of the plate perpendicular to the air flow is 1 m. At what distance from the leading edge does the flow become turbulent? ________m What is the heat transfer at the point of transition? ___________W What is the total heat transfer along the length of the plate where the flow is laminar? __________W
Typically, air is heated in a hair dryer by blowing it across a coiled wire through which an electric current is passed. Thermal energy is generated by electric resistance heating within the wire and is transferred by convection from the surface of the wire to the air. Consider conditions for which the wire is initially at room temperature, T;, and resistance heating is concurrently initiated with airflow att = 0. q Air Too, h 001 Coiled wire (ro, L, k, p, cp) 0000 Pelec Airflow ווי SU