A long, cylindrical, electrical heating element of diameter D = 14 mm, thermal conductivity k = 251 W/m - K, density p = 2,805 kg/m3, and specific heat cp = 903 J/kg · K is installed in a duct for which air moves in cross flow over the heater at a temperature and velocity of 30°C and 9 m/s, respectively. (a) Neglecting radiation, estimate the steady-state surface temperature when, per unit length of the heater, electrical energy is being dissipated at a rate of 1,033 W/m.

A long, cylindrical, electrical heating element of diameter D = 14 mm, thermal conductivity k = 251 W/m - K, density p = 2,805 kg/m3, and specific heat cp = 903 J/kg · K is installed in a duct for which air moves in cross flow over the heater at a temperature and velocity of 30°C and 9 m/s, respectively. (a) Neglecting radiation, estimate the steady-state surface temperature when, per unit length of the heater, electrical energy is being dissipated at a rate of 1,033 W/m.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A hot steel ball of 5 mm in diameter initially at 100 oC is left to cool down in air at 20 oC. Assume a constant convective heat transfer coefficient h = 15 W/m2K through the course of the cooling process. Cp, steel = 0.49 kJ / kg K , k,steel = 45.0 W / m K , rho, steel = 7800 kg/m^3 Cp,air = 1.00 kJ/kg K ; k_air = 0.025 W / m K; rho,air = 1.2 kg/m^3 a) Calculate the rate of convective heat transfer when the steel ball is uniformly at 100 oC. b) Assuming the steel as a lumped system, find the temperature of the steel ball after 0.5 s.
QI/ An aluminum rod 4.0 cm in diameter and 10 cm long protrudes from a wall that is maintained at 250°C, and air at 40°C is forced it at a velocity of 50 m/s. If the surface emissivity is 0.7, Calculate the total heat loss per unit length if the walls of the enclosing room at 15 °C ?. T, h. T A,= A
Metal plates of size 60 cm × 50 cm, and thickness 1 cm are initially at 100◦C. They are to be cooled by blowing chilled air at 2 m/sec over both surfaces, the flow being directed along the side whose length is 60 cm. Incoming air temperature is 10◦C. Data for the metal: ρ = 7854 kg/m3, cp = 434 J/kg/K, k = 60.5 W/m/K Data for air: Use values at 50◦C. (a Determine the convective heat transfer coefficient at the surfaces of the plates.(b Determine whether lumped system analysis is applicable(c Assume the convection coefficient is constant, determine how much time is necessary for the temperature of the plates to drop to 25◦C.(d Estimate the total heat lost by a plate when it has reached 25◦C.
An electric resistance heater is embedded in a long cylinder ofdiameter 30mm. When water with a temperature of 25 C and velocityof 1m/s flows crosswise over the cylinder, the power per unit lengthrequired to maintain the surface at a uniform temperature of 90 C is28kW/m. When air, also at 25 C, but with a velocity of 10m/s isflowing, the power per unit length required to maintain the samesurface temperature is 400W/m. Calculate and compare the convectioncoefficients for the flows of water and air.
Heat transfer. Show all steps for solution
Small potato balls of 0.5 cm radius (can be approximated as a sphere) baked in the oven and initially at a uniform temperature of 160°C. Assume, potatoes have a density of 650 kg/m, specific heat of 3400 J/kgK and conductivity of 1 W/mK. You want to eat potatoes quickly without burning your tongue so that you have decided to cool them down with forced convection. Air h, T. hot potato initially Air temperature is 20°C and the convective heat transfer coefficient is 140 W/m?K. Calculate the time (in seconds) required for its surface temperature to drop 90°C.
2.0 Engine oil at 100°C and a velocity of 0.25 m/s flows over both surfaces of a 0.8-m-long flat plate maintained at 20°C.Determine:(a) The velocity and thermal boundary layer thicknesses at the trailing edge.(b) The local heat flux and surface shear stress at the trailing edge.(c) The total drag force and heat transfer per unit width of the plate.
KNOWN: Expression for face-averaged Nusselt numbers on a cylinder of rectangular cross section. Dimensions of the cylinder. FIND: Average heat transfer coefficient over the entire cylinder. Plausible explanation for variations in the face-averaged heat transfer coefficients. SCHEMATIC: Air V = 10 m/s T = 300 K c = 40 mm ASSUMPTIONS: (1) Steady-state conditions, (2) Constant properties. d = 30 mm
Plzz help
Air stream at 27 degrees * C is moving at 0.3 m/s across a 100 W electric bulb at 127 degrees * C. If the bulb is approximated by a 60 mm diameter sphere, estimate the heat transfer rate and the percentage of power lost due to convection.
نقطتان )2( Q1/ Give True or False for the following statements: a) In a uniformly accelerated rectilinear motion, the acceleration of the particle is zero True fales
A long aluminum wire of diameter 4 mm at a temperature of 370°C is subjected to cross air flow at 30°C at a velocity of 5.8 m/s. What is the conveçtive heat transfer coefficient (W/m".K)? Air properties: v =3.455×10¨ m /s, Pr = 0.6974, k = 0.03779 W/m.°C -5 Select one: