A tube bank uses an aligned arrangement of 15-mm-diameter tubes with Sy= S = 30 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 7 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m?

A tube bank uses an aligned arrangement of 15-mm-diameter tubes with Sy= S = 30 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 7 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Consider two cases involving parallel flow of dry air at V = 1.5 m/s, T=45°C, and atmospheric pressure over an isothermal plate at T = 20°C. In the first case, Rex, = 5 x 105, while in the second case the flow is tripped to a turbulent state at x = 0 m. At what x -location, in m, are the thermal boundary layer thicknesses of the two cases equal? What are the local heat fluxes, in W/m², at this location for the two cases? x = 9jam 9 turb II = i i m W/m² W/m²
PLEASE ANSWER COMPLETELY AND CLEAN FOR AN UPVOTE!!
An oil preheater consists of a single tube of 10-mm diameter and 5-m length, with its surface maintained at 180°C by swirling combustion gases. The engine oil (new) enters at 70°C. What flow rate, in kg/h, must be supplied to maintain an oil outlet temperatur of 105°C? What is the corresponding heat transfer rate, in W? m = kg/h W
Calculate the convective heat transfer rate via the top and the two side walls of a refrigerated box trailer as shown in the figure. The trailer is cruising at a rate of 70 mph (31.3 m/s). The box trailer dimensions are 16 m long, 4.1 m high, and 2.6 m wide. Assume that the surface of the trailer is at uniform temperature of 10°C. The air temperature is 30°C. Because of the presence of the prime-mover in the front, the air flow can be assumed to be turbulent when it encounters the trailer. 187.4 kW Walls. Prime-mover 16 m 2.6 m
A vehicle carrying refrigeration box is moving with a speed of 24 m/s on a road withambient temperature of 323 K. The dimensions of box are 3 m(H) × 4 m (W) × 10 m (L).Assume a wall temperature of 283 K and air flow is parallel to the longest side of the box.Neglecting the heat loss from the front side and backside of the box, calculate heat lossfrom four surfaces. For flow over flat surfaces useNu = 0.036(Re)0.8(Pr)1/3The properties of air at bulk mean temperature are : = 1.165 kg/m3, Pr = 0.701, cp = 1005 J/kg – K,  = 16 × 10–6m2/s
Air (pressure 1 atm) enters a circular pipe 5 cm in diameter at 20 °C with an average speed of 5 m/s. The tube wall is maintained at a constant surface temperature of 160°C, and the mean outlet temperature is 80°C. Estimate the length of the tube. Mainly, I also need the solution from concepts of how the heat flow behaves in the system, it can be with a diagram.
In the final stages of production, a pharmaceutical is sterilized by heating it from 25 to 75°C as it moves at 0.21 m/s through a straight thin-walled stainless steel tube of 12.7-mm diameter. A uniform heat flux is maintained by an electric resistance heater wrapped around the outer surface of the tube. If the tube is 10 m long, what is the required heat flux? If fluid enters the tube with a fully developed velocity profile and a uniform temperature profile, what is the surface temperature at the tube exit? Fluid properties may be approximated as p = 1000 kg/m³, c, = 4000 J/kg-K, µ = 2x 103 kg/s-m, k = 0.8 W/m-K, and Pr = 10. Determine the required heat flux, W/m². q! = i W/m? Determine the surface temperature at the tube exit, in °C. i °C S,0
The 340-lb force is applied at point A of the bracket. Determine the moments of this force about point B, about point C, and about the line BC. "Ac k) lb-in. k) lb-in. B 16" 142° 21" Answers: Mg = (i Mc-(i MBC= 18" + i+ 340 lb Mi lb-in. j+ j+ Mi
Please do it on a paper. Thank you
Water flows in a duct having a cross-section of 10x20 mm with a mean bulk diameter of 15.56 deg C. If the duct wall temperature is constant at 60 deg C and fully developed laminar flow prevails. a.) Calculate the heat transfer coefficient, h in W/m2-deg Cchoices: (405, 305, 151, 252) b.) What is the thermal conductivity of water at the given temperature, k in W/m-deg Cchoices: (0.604, 0.6, 0.585, 0.595) c.) Calculate the heat transfer rate per unit length in W/mchoices; (605, 366, 505, 404)
A tube bank uses an aligned arrangement of 15‐mm‐diameter tubes with ST=SL=30 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 5 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m?