A tube bank uses an aligned arrangement of 15-mm-diameter tubes with S = S = 30mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 7 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m? 89 kW/m

A tube bank uses an aligned arrangement of 15-mm-diameter tubes with S = S = 30mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 7 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m? 89 kW/m

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.23P

See similar textbooks

Similar questions

6.1 Determine the heat transfer coefficient at the stagnation point and the average value of the heat transfer coefficient for a single 5-cm-OD, 60-cm-long tube in cross-flow. The temperature of the tube surface is , the velocity of the fluid flowing perpendicular to the tube axis is 6 m/s, and the temperature of the fluid is . Consider the following fluids: (a) air, (b) hydrogen, and (c) water.
6.3 Steam at 100 kPa and is flowing across a 5-cm- OD tube at a velocity of 6 m/s. Estimate the Nusselt number, the heat transfer coefficient, and the rate of heat transfer per meter length of pipe if the pipe is at .
Please no written by hand solutions
please answer asap with clear solution
A tube bank uses an aligned arrangement of 15-mm-diameter tubes with Sr = SL = 30 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 40°C, while flue gases at 427°C and a velocity of 17 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427°C. What is the total rate of heat transfer per unit length of the tubes in the bank, in kW/m? q' = kW/m i
Please help me get the correct answer quickly, please. :((
Please show all steps, not Ai generated, has been wrong before. I need to understand the process.
can you please work it all please please
Engine oil is heated by flowing through a circular tube of diameter D = 50 mm and length L = 25 m and whose surface is maintained at 150°C. (a) If the flow rate and inlet temperature of the oil are 0.5 kg/s and 20°C, what is the outlet temperature Tm,o? What is the total heat transfer rate q for the tube?
A tube with 2 cm inner diameter and 1 m length has uniform wall temperature water at 300 k with fully developed Velocity enters the tube with a mean Velocity of 0.05 m/s. The mean water exit temperature is 350 k. (a) find the surface temperature by using a thermally developed flow correlation? (b) if the Boundary Condition was Constant heat flux what would be the required heat flux? (C) for part b calculated the heat transfer coefficient and wall temperature at the middle of the tube?
Current Attempt in Progress Consider pressurized water, engine oil (unused), and Nak (22 %/78%) flowing in a 20-mm-diameter tube. (a) Determine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluids when the fluid temperature is 366 K and the flow rate is 0.014 kg/s. (b) Determine the mass flow rate, in kg/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for water and engine oil at 300 and 400 K and a mean velocity of 0.018 m/s. Part A Your answer is incorrect. Determine the mean velocity, in m/s, the hydrodynamic entry length, in m, and the thermal entry length, in m, for each of the fluids when the fluid temperature is 366 K and the flow rate is 0.014 kg/s. Liquid water engine oil Nak (m/s) ! i XALA(M) xer (m) Attempts: unlimited Submit Answer
A tube bank uses an aligned arrangement of 10-mm-diameter tubes with ST = SL = 20 mm. There are 10 rows of tubes with 50 tubes in each row. Consider an application for which cold water flows through the tubes, maintaining the outer surface temperature at 27°C, while flue gases at 427°C and a velocity of 5 m/s are in cross flow over the tubes. The properties of the flue gas may be approximated as those of atmospheric air at 427oC. What is the total rate of heat transfer per unit length of the tubes in the bank?