PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The machine part ABC is supported by a frictionless hinge at B and a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. The force Pis applied on the wedge to push it to the right. Given, F= 680 N. 200 mm -250 mm Problem 08.049.c - Reactions at hinge C The value of the component By Is The value of the component By Is D 10° Determine the components of the corresponding reaction at B N (Click to select) N(Click to select) v

PROBLEM - ASSIGN ALL PARTS NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. The machine part ABC is supported by a frictionless hinge at B and a 10° wedge at C. The coefficient of static friction is 0.20 at both surfaces of the wedge. The force Pis applied on the wedge to push it to the right. Given, F= 680 N. 200 mm -250 mm Problem 08.049.c - Reactions at hinge C The value of the component By Is The value of the component By Is D 10° Determine the components of the corresponding reaction at B N (Click to select) N(Click to select) v

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The 75-lb force P is applied to the 160-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.50, μ = 0.38. P Answer: F= tel Hk lb
View Policies Current Attempt in Progress The 86-lb force Pis applied to the 210-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force Fexerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume 4, = 0.43, Hg = 0.34. P Answer: F = i Ib
The 99-lb force P is applied to the 240-lb crate, which is stationary before the force is applied. Determine the magnitude and direction of the friction force F exerted by the horizontal surface on the crate. The friction force is positive if to the right, negative if to the left. Assume μ = 0.43, μ = 0.35. P Answer: F= Hs Hk lb
3. The tape shown slides around two fixed pegs each of radius 30 mm as shown. If T1 = (0.1P in newton) and T2 = (0.4P in newton, determine the coefficient of friction between the tape and the pegs. T1 R = 30 ---f P=65 T2 50 mm 50 mm R = 30
Dětérmine the magnitude of the force P, acting as shown, that will cause the 120 N crate to move. Assume the coefficient of static friction between the crate and the ground are ps = 0.3. 120N O 45 N O 50 N O 20 N O 36 N
For the design of the band brake shown, find the couple M required to turn the pipe in the V-block against the action of the flexible band. A force P = 31 lb is applied to the lever, which is pivoted about O. The coefficient of friction between the band and the pipe is 0.26, and that between the pipe and the block is 0.35. the weights of the parts are negligible. B M * 10" 45% 00 35° 35° 5 A Answer: M = | the tolerance the tolerance is +/-5% lb-in. 16" P
H.W.1 A steel pipe that contains castor oil (p=1.8624 slug/ft) is 6 ft in diameter. Determine the forces exerted on the portion labeled A-B in Figure below if the pipe is filled halfway. Determine also the location of the forces. Pipe length (into the paper) from joint to joint is 8 ft. 6 ft Fy Ih Fx A A A
5. A steel tape is 150 m. long at a standard pull of 65 N. Compute the pull correction in mm if during measurement the applied pull is 42 N. The tape has a cross sectional area of 3.18 mm² and a modulus of elasticity E = 200,000 MPa. A. -5.772 C. -4.321 B. -5.425 D. -5.936 6. The volume of a closed cylinder is numerically equal to its lateral area. The height is 18 m. Find the volume in m³. A. 198.7 C. 321.4 B. 257.8 D. 226.2 7. The offset distance from PC to PT of a simple curve is 24 m. The angle of intersection of the tangents is 19.5°. If the stationing of PT is 12 + 365.24, what is the stationing of PI? A. 12+295.47 SEC. 12 + 293.34 B. 12 + 296.32 D. 12 + 294.73 T
A 10-kg cylinder D, which is attached to a small pulley B, is placed on the cord as shown. Determine the largest angles θ so that the cord does not slip over the peg at C. The cylinder at E also has a mass of 10 kg, and the coefficient of static friction between the cord and the peg is μs = 0.1.
1. Solve the problems completely. 2. Support your solutions with diagrams. 3. No short-cut in your solution 4. Encirle your final answer. P1. Compute the acceleration of body B and the tension in the cord attached to it. 300 lb 4-0.20 200 lb A P2. Two blocks A and B are released from rest at 30 degree incline when they are 50 ft. apart. The coefficient of friction under block A is 0.20, and that un der block Bis 0.40. Compute the elapsed time until the blocks t ouch.
THE COEFFICIENT OF STATIC FRICTION BETWEEN THE BLOCK AND THE PLANE IS µs = 0.2. DETERMINE THE MAXIMUM VALUE OF WEIGHT W WITHOUT CAUSING THE 50-LB BLOCK TO SLIP. D W 45° Answer:
An extruded beam has the cross section shown. It is given that V = 48 kN. NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. D 10→ 0 I E 10 G -70 Dimensions in mm B 40 100 Determine the location of the shear center O. The value of e is mm.