Problem 5: A 300 mm x 150 mm venturimeter is provided in a vertical pipeline carrying oil of specific gravity 0.9, flowing upward. The difference in elevation of the throat section and entrance section of the venturimeter is 300 mm. The differential U- tube manometer shows a gauge deflection of 250 mm. Calculate i) The discharge of oil ii) The pressure difference between entrance and Throat section. Take : coefficient of discharge of venturimeter is 0.98 150 mm Throat 300 mm Inlet 250 mm 300 mm

Problem 5: A 300 mm x 150 mm venturimeter is provided in a vertical pipeline carrying oil of specific gravity 0.9, flowing upward. The difference in elevation of the throat section and entrance section of the venturimeter is 300 mm. The differential U- tube manometer shows a gauge deflection of 250 mm. Calculate i) The discharge of oil ii) The pressure difference between entrance and Throat section. Take : coefficient of discharge of venturimeter is 0.98 150 mm Throat 300 mm Inlet 250 mm 300 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: (Answer: m = 2.578 kg/s) 8) A venturi meter measures the flow of water in a 75 mm diameter pipe. The…

Q: Please give detailed explanations and show your work clearly - I will be using this to study for an…

A: The Navier–Stokes equations contains a set of differential equations which describes the motion of…

Q: Water at 4.4oC with a density of 1000 kg/ m3 and a viscosity of 1.55 cP is to flow through a…

Q: Calculate a) The pressure head supplied by the pump, b) The total head loss between point b and 2.…

Q: During Extension of vertical cylinder At Extension (when cylinder is stopped) Pressure Reading PSI…

Q: anometer being used to indicate the pressure difference between two points in a fabricated system.…

Q: Pump head, hp, can be formulated as, h, = 22 - z1 + hm + he Where, E h = EK and hy = Table 1: Minor…

A: a) Volume flow rate =0.006 m3/s ( given) Radius = 2cm = 0.02m Cross section area= 3.14 × 0.022…

Q: Problem 1: For the system shown in the diagram below, let 4z = 80 m and L = 185 m of cast iron pipe…

A: To determine:Pipe diameter(D)

Q: (8.18) Water flows at a rate of 25 gallons per minute in a new hori- zontal 1.5-in.-diameter…

Q: A viscosity motor/pump is shown in figure below. The rotor is concentric within a stationary…

A: The value are .The flow rate is .The dynamic viscosity is .

Q: Find the velocity of flow

Q: For the flow configuration shown, you are required to design a pump station to transfer water from…

A: For designing of any pump station, various types of losses are considered. Losses such as major…

Q: 3. Water at the rate of 30 litres/sec. is flowing through a 0.2 m. 1.D. pipe. A venturi meter of…

Q: A 300mm * 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

A: We have, d1=300 mm=0.3 md2=150 mm=0.15 m,Cd=0.98 Reading of different manometer x=200 mm of Hg=0.2 m…

Q: Problem solving Air Water flows through a horizontal plastic pipe with a diameter of 0.2 m at a…

A: To Find : The friction factor, Given : The diameter of pipe is d=2m The velocity of air is v=10 cms…

Concept explainers

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.

Question

100%

Problem 5:
A 300 mm x 150 mm venturimeter is provided in a vertical pipeline carrying oil of specific gravity 0.9, flowing upward. The
difference in elevation of the throat section and entrance section of the venturimeter is 300 mm. The differential U – tube
manometer shows a gauge deflection of 250 mm.
Calculate
i) The discharge of oil
ii) The pressure difference between entrance and Throat section.
Take : coefficient of discharge of venturimeter is 0.98
150 mm
Throat
300 mm
Inlet
250 mm
300
mm

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

2. A calibration test of a 15 mm circular sharp-edged orifice in the end of a 50 mm pipe showed a discharge of 0.8 liter per second of water when the pressure head on the center line of the pipe just upstream from the orifice was 2.70 m. The diameter of the jet at the vena contracta was found to be 12 mm. Compute the three orifice coefficients. Compute each coefficient independently from the other coefficients.
Describe the methodology for obtaining the pump curve in a project, where data are collected at five points with different pressures in the pump (10 psi, 15 psi, 20 psi, 25 psi and 30 psi), where to find these Q flow rates a 1000 ml bottle is used and the time needed to fill it is timed, for each of the pump's five pressure points. The gauge pressure H in meters of water column achieved should also be observed, in order to construct the HxQ graph of the pump.
A service truck transfers hydraulic oil with a kinematic viscosity of 200 cSt through a 2-in. I.D. hose 100 ft. long to a bulldozer at a flow rate of 50 gal/min. What is the pressure drop between the service truck and the bulldozer if the fluid Sg is 0.85?
Nitrogen gas under a pressure pn = 15 psig is used for pumping kerosene at 25°C (density = 816 kg/m3, viscosity = 1.81 cP) through an elevation increase of 6 m. If there is an effective length of 45 m of nominal 2-in. schedule No. 40 pipe (commercial steel) between the two tanks, what is the flow rate of kerosene? Neglect exit kinetic-energy effects.
2. An inclined venturi tube containing water has an inlet of 300 mm diameter and a throat of 150 mm diameter. The difference in head between the inlet and the throat is 250 mm. Neglecting losses, calculate the discharge through the venturi meter. Alir 250 mm 300 mm Diam 150 mm Diam -Water
A horizontal venturimeter with inlet and throat diameter of 160 mm and 60 mm respectivelyis used measure the flow of an oil of specific gravity 0.8. if the discharge of oil is 0.05 m3/s, find the deflection of oil mercury differential manometer. Take venturimeter constant=1.
SOLVES TEP BY STEP DONT USE CHATGPT DONT USE AI 3. An oil of viscosity 1.8 cp and relative density 0.8 is contained in an open tank located above the application site. A 1.5-inch diameter pipe extends vertically from the bottom of the tank and is 5 m long. The oil level in the tank remains constant at 3 m above the bottom of the tank. In a case with friction the discharge speed can be obtained in the form of the following Equation. Calculate the flow rate of oil discharged per hour. Assume that the pipe is commercial steel (ε=0.05 mm). V= 2gh +f-
fluid mechanics
Please solve this in quickly please please please
Fluid of specific gravity of 0.78 flows in a 127mm diameter pipe. Find the critical velocity in m/s. The absolute viscosity is 8.14x10^-2 Pa-s