A horizontal venturimeter with inlet and throat diameter of 160 mm and 60 mm respectively is used measure the flow of an oil of specific gravity 0.8. if the discharge of oil is 0.05 m3 /s, find the deflection of oil mercury differential manometer. Take venturimeter constant=1.

Q: a. A U tube differential manometer containing mercury was used to measure the difference of…

A:

Q: Cylinder has a bore area of 318cm2 and volume 205 cm/min. Calculate the discharge of a pump delivery…

A: Given data,  A= 318 cm2  Velocity= v= 205 cm/min

Q: Give the classification of flow meters

A: Flow meters can be classified into two categories - Mass flow meters Volume flow meters

Q: ong Stag 2. The following data relate to an inclined venturimeter: Diameter of the pipe line = 400…

A:

Q: Flow Pump 6-in Schedule 40 4-in Schedule 40 4 in Engine Oil 30 in Mercury (sg =13.54)

A: Calculate the pressure change from point 1 to point 2. P1-ρoilg4 in-ρhgg30 in+ρoilg34…

Q: A Venturi meter with a 15 cm I.D. at inlet and 10 cm I.D. at throat is laid with its axis horizontal…

A:

Q: A pipeline carrying 0.257 m/s water is reduced suddenly from 400 mm to 250 mm diameter (Take Cc…

A: Note: As per Bartleby guidelines only one question has to be solved. So upload other questions…

Q: Q1) Using a system similar to that shown in figure, if air pressure p = 50 kPa., and the depth h₁ =…

A:

Q: Question 2. la0 mm diameter siphon draws water from the reservoir. Considering that the elevation…

A: Given diameter =4mm=0.004 m h(1)=1m h(2)=1 m

Q: À venturimeter is inserted a 150 mm dia If the differential head indicated by the rate of flow is 80…

A:

Q: A 300mm * 150 mm venturimeter is inserted in a vertical pipe carrying water flowing in upward…

A:

Q: A-20 in Oil SG 0.86 51t 0.8 t A-50 in. SG 2.5

A:

Q: (b) A venturi meter with diameter at inlet D, and throat diameter D2, is used for measuring the flow…

A:

Q: -Example the values. asystem total head. against. for the initial condition, show below - give the…

A:

Q: 4: A 60 mm diameter sharp edged orifice is placed in a pipe line to measure flow rate. If the…

A:

Q: P/ IF the Flow vate through the Pum 0.1 mls of water, Find the Punp head.The manometer reading is…

A: The pump head is 14.7157 m.

Q: The distribution system requires to lift water to an area with an average elevation of 100 mamsl…

A: The Answer is below

Q: 0 oil volume flow rate

A: given:

Q: Cylinder has a bore area of 324cm2 and volume 195 cm/min. Calculate the discharge of a pump delivery…

A: Data given-  A = 324 cm2 = 324 × 10-4 m2  Velocity = 195 cm/min  Velocity = 195 × 10-2 m/min

Q: each pipe may be taken 0.03. 100 mm diameter, 200 m length Atmosphere B 100 mm diameter, 100m length…

A: Calculated discharge in each pipe.

Q: eter 20mm and vertical int 'B') water is flow t a is 0.008. Pressure hea

A:

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: As per bartleby guidelines we are allowed to solve 1st 3 subparts of question. Please post remaining…

Q: Q3/ The pipe has a different diameter: diameter (D1 = 4 m) changes into (D2= 6 m). The water…

A:

Q: Find the discharge of the pipe of diameter 20 mm with the velocity of water 5.25m/s in litres/sec…

A:

Q: аз in. IS installed in a 6 in. pipe-line. The pressure at the entrance to the meter is 10 psi gauge…

A: A venturi meter(diameter) =3 ininstalled in =6 inA1V1=A2V2π4×6122×v1=π4×3122×v2v1=0.25 v2v2=4 v1…

Q: C2. A conical tube is fixed vertically with its smaller end upwards and it forms a part of the…

A: Given: Velocity of smaller end (V1)=4.3m/sVelocity of larger end (V2)=2.1m/sLength of the conical…

Q: B1. A crude oil of specific gravity 0.75 is flowing through a pipe of diameter 350 mm and the…

A:

Q: Calculate the minimal head of the pump required to pump 1 m³ of water per second to the height 10 m…

A: Minimum head is the suction head required in centrifugal pump which avoids cavitation in pump…

Q: Water flows into junction J from reservoirs A and Bthrough connecting pipes, the head loss through…

A: Given:Head loss in pipe A=10QA2Head loss in pipe B=4QB2water level at A=25.9 mwater level at B=18…

Q: Calculate the discharge throug

A: To find Discharge

Q: FIND THE TOTAL DYNAMIC HEAD IN METER OF THE PUMPING SYSTEM DRAW THE SCHEMATIC DIAGRAM OF THE PUMPING…

A:

Q: The distribution system requires to lift water to an area with an average elevation of 90 mamsl from…

A:

Q: Centrifugal pump has differential pressure=15 bar and use to transport oil between two separators.…

A: P_atm = Atmospheric Pressure (assumed to be 101.3 kPa at sea level)P_vap = Vapor Pressure of the…

Q: (Enter only the values by referring the unit given. Also upload the hand written answers in the link…

A: Given: The specific gravity of crude oil is s=0.75. The diameter of pipe is d=325 mm. The…

Q: Find the force required to hold the blade in position, if the jet weight (100kg) and discharge…

A:

Q: Taking atmospheric pressure head = 10.3 m of water. A 100 mm diameter horizontal pipe has a…

A:

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.