PROBLEM 3. The assembly shown constructed from a steel bolt with a diameter of 8 mm and fits and a magnesium sleeve with an inner diameter of 10 mm and an outer diameter of 12 mm. The length of the sleeve is 150 mm. The assembly is originally at a temperature of T1 temperature is raised to a final value of T2 = 120°C. If there is gap of 0.1 mm between sleeve and the rigid washer at end B before the heating, determine the average normal stress in the bolt and the 20°C and then the %3D %3D sleeve. Est = 200 GPa, Emg = 44.7 GPa, ast = 14(10°)/°C, amg =. 26(10)/"C. %3D %3D Rigid washers 150 mm 0,1 mm

PROBLEM 3. The assembly shown constructed from a steel bolt with a diameter of 8 mm and fits and a magnesium sleeve with an inner diameter of 10 mm and an outer diameter of 12 mm. The length of the sleeve is 150 mm. The assembly is originally at a temperature of T1 temperature is raised to a final value of T2 = 120°C. If there is gap of 0.1 mm between sleeve and the rigid washer at end B before the heating, determine the average normal stress in the bolt and the 20°C and then the %3D %3D sleeve. Est = 200 GPa, Emg = 44.7 GPa, ast = 14(10°)/°C, amg =. 26(10)/"C. %3D %3D Rigid washers 150 mm 0,1 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Fast asap
Note:: I need this solution within an hour plzz
Need correctly in neat and clean handwritten solution explaining every steps
#2 will upvote to anyone who will answer
22. two decimal places
The picture below Consist a brass ( EB = 100 Gla and AB and a Aluminum [ EA₁ = 73GPa | AA! each red exists a non- deformable rigid plate. The rods are stress free at 25°C. If the coefficient of thermal expansion for staat is taken 13.106 [m/m°c ] of a steel (E₂ -200CHPA and As = 1500mm ² = 2000 mind) JAT aluminiscent 2 = 1500 mm ² ) kod between at ds and temperature increased to up re increased to 350°C. A steel Find reactionary forces at A_and_D_ Considering RA = Rai and Rp = - Rp₁" ? Also find the deflection of plate B. 1.5 m a 18 = 19,10`6 [m/m="c] α = 24,10 € AL B Brass Im t D Aluminum 1.5m [m/m="c} Fant Fall = $6
A 1.0 meter long A36 steel rod with a diameter of 40mm is lightly attached at both end of the rod, end A and end B. A collar is located in the center of the rod. The initial temp is 60 degrees C. The final temperature is 35 degrees C. Determine the force that must be applied to the collar so that the reaction at B is zero.Given:Delta T=25 degrees CE for A36 steel: 200 GPaCoeff of thermal expansion: 12(10^-6)/degree C
A thin cylinder 500 mm in diameter is made by providing a longitudinal lap joint with 8 mm shop fillet weld on two side as shown in figure. What will be the design pressure (in N/mm2) of fluid that can be allowed in the cylinder based on the strength of weld? Grade of steel used for load is Fe410. Weld
What is the maximum concentrated load that can be applied at the end of an embedded hollow pipe, made of AISI 1020 steel? Take 10.16 cm for the outside diameter, and 6.35 cm for the inside diameter. The length of the pipe is 183 cm. Its maximum deflection must not exceed 5.08 cm. Neglect the weight of the pipe. Answer 22816 N
A uniform bar is connected to a tapered rod 2. Both are subjected to axial loads as shown . If P = 7kN Determine the axial deformation of uniform bar 1 (in mm) Indicate negative sign if compression. Complete solution no round off.
At a temperature of 37.4 °C a 0.49-mm gap exists between the ends of the rods shown. At a later time when the temperature has reached 128.7°C, determine the change in length of the steel rod if L = 328.25 mm and M = 215 mm. Round off the final answer to four decimal places.
r Two Example (2) 8- A compound bar is constructed from three.. wide by 12mm thick together to form a bar somm wide 30 The middle bar is of aluminum alloy for which F-70 GP= outside of brass with E-100 MPa. If the bars are initia at 18c and the temperature of the whole assembly is to to So C, determine the stresses set up in the brass and the Kg = 18 510 Solutions2 FB = FAL FB So*12*10 63 Ext. + Comp. = (XAI - XB) L.A.T. FB.L FAL.L AAL.EAL Ag Eg = DAL + From these equation & FAL=3984 N FB 1992. N 1992 50*121610-6 FB AB -6 XA => 22 *10°-=-=- = (XAL-XB) LAT FAL *100*109 So*12*10% 70 4109 FAL 3984 AAL SO#1210-6 SB = SAL How find that?! = 32. MPa (Ton) FAL. L AP EA = (22-18) x 10² (50-18) XIF_P=15 KN (camp.) Find O'B and GAL F₁+ 2FB = 15 6.64 MPa: (comp)... L FB.L AB. E.B ww.as 17 Brass AL Brass